Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052110 ECD SYSTEM(for i-ART) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P0046  Turbocharger / Supercharger Boost Control Solenoid Circuit Range / Performance  P0047  Turbocharger/Supercharger Boost Control "A" Circuit Low  P0048  Turbocharger/Supercharger Boost Control "A" Circuit High  


DESCRIPTION

These DTCs indicate that the DC motor of the turbocharger sub-assembly is malfunctioning. The ECM monitors the DC motor current to detect an open or short in the DC motor circuit. If the current meets certain criteria, the ECM stores a DTC and illuminates the MIL immediately.

The DC motor is used to operate the nozzle vane of the turbocharger sub-assembly. The nozzle vane opens and closes to change the velocity of exhaust emissions in order to control the turbo pressure. The ECM varies the duty ratio of the DC motor in accordance with the driving conditions.

If the nozzle vane is stuck closed (DC motor stuck off), drivability may deteriorate at wide open throttle. If the nozzle vane is stuck open (DC motor stuck on), drivability may deteriorate at intermediate throttle positions or the engine power may be insufficient.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0046 Turbocharger / Supercharger Boost Control Solenoid Circuit Range / Performance Either condition is met when the motor is operating (1 trip detection logic):
·

The DC motor duty ratio exceeds the threshold for 0.5 seconds for the specified number of times (in terms of time, this amounts to 100 seconds or more).

·

DC motor current is 2.2 A or higher for 5 seconds or more.


·

Open or short in DC motor (turbocharger sub-assembly) circuit

·

DC motor (turbocharger sub-assembly)

·

Turbocharger nozzle vane is stuck or movement is irregular


Comes on DTC stored
P0047 Turbocharger/Supercharger Boost Control "A" Circuit Low The DC motor duty ratio is 80% or more and the motor current is 0.5 A or less for 3 seconds or more (1 trip detection logic).
·

Open in DC motor (turbocharger sub-assembly) circuit

·

DC motor (turbocharger sub-assembly)

·

Turbocharger nozzle vane is stuck or movement is irregular


Comes on DTC stored
P0048 Turbocharger/Supercharger Boost Control "A" Circuit High Overcurrent is detected 25 times or more (0.4 seconds or more) (1 trip detection logic).
·

Short in DC motor (turbocharger sub-assembly) circuit

·

DC motor (turbocharger sub-assembly)

·

Turbocharger nozzle vane is stuck or movement is irregular


Comes on DTC stored

HINT:
·

If DTC P0046, P0047 and/or P0048 is stored due to the nozzle vane being stuck closed, the following symptom may appear:

·

Vehicle surge when driving with full load


·

If DTC P0046, P0047 and/or P0048 is stored due to the nozzle vane being stuck open, the following symptoms may appear:

·

Lack of power

·

Vehicle surge or hesitation under light or medium load




CONFIRMATION DRIVING PATTERN

P0046
DTC Detection Drive Pattern Ignition switch ON for 5 seconds

P0047, P0048
DTC Detection Drive Pattern 2 seconds after engine is started, race engine for 1 second

WIRING DIAGRAM

A205135E40
2.063,1.396 2.26,1.573 0.198,0.177 10 false 1 5.427,0.74 5.615,0.917 0.188,0.177 10 false 15 5.438,1.427 5.615,1.604 0.177,0.177 10 false 14 5.688,1.281 5.938,1.458 0.25,0.177 10 false M- 5.99,2.021 6.385,2.198 0.396,0.177 10 false ECM 5.688,0.625 5.917,0.802 0.229,0.177 10 false M+ 2.073,0.729 2.271,0.906 0.198,0.177 10 false 2 0.646,2.031 1.313,2.219 0.667,0.188 10 false DC motor 5.99,1.833 6.385,1.99 0.396,0.156 10 false C164 0.667,1.854 0.969,2.031 0.302,0.177 10 false C41 1.802,1.208 2.052,1.385 0.25,0.177 10 false M- 1.792,0.542 2.021,0.719 0.229,0.177 10 false M+

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0046, P0047 AND/OR P0048)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
P0046, P0047 and/or P0048 is output A
P0046, P0047 and/or P0048 and other DTCs are output B


HINT:

If codes other than P0046, P0047 and/or P0048 are output, perform troubleshooting for those DTCs first.




A

2.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR OPERATION)

B

2.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR OPERATION)

Result:
Proceed to
OK
NG



OK

NG

3.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR RESISTANCE)
3.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR RESISTANCE)
a.
C217215C05
0.12,0.111 0.297,0.288 0.177,0.177 10 *a
*a Component without harness connected
(DC Motor)


Disconnect the DC motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (M-) - 2 (M+) Always 1 to 100 Ω



c.

Reconnect the DC motor connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (DC MOTOR - ECM)

NG

6.REPLACE TURBOCHARGER SUB-ASSEMBLY
4.CHECK HARNESS AND CONNECTOR (DC MOTOR - ECM)
a.

Disconnect the DC motor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C41-1 (M-) - C164-14 (M-) Always Below 1 Ω
C41-2 (M+) - C164-15 (M+) Always Below 1 Ω
C41-1 (M-) or C164-14 (M-) - Body ground Always 10 kΩ or higher
C41-2 (M+) or C164-15 (M+) - Body ground Always 10 kΩ or higher



d.

Reconnect the DC motor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE TURBOCHARGER SUB-ASSEMBLY

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Turn the ignition switch to ON for 5 seconds or more.


e.

2 seconds after the engine is started, race the engine for 1 second.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END