| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P168A | Injector #1 Internal EEPROM Malfunction | The EEPROM in the injector assembly is malfunctioning (EEPROM access (write or read) cannot be performed) for 3 seconds or more.
(1 trip detection logic) |
No. 1 injector assembly | - | DTC stored |
| P168B | Injector #2 Internal EEPROM Malfunction | The EEPROM in the injector assembly is malfunctioning (EEPROM access (write or read) cannot be performed) for 3 seconds or more.
(1 trip detection logic) |
No. 2 injector assembly | - | DTC stored |
| P168C | Injector #3 Internal EEPROM Malfunction | The EEPROM in the injector assembly is malfunctioning (EEPROM access (write or read) cannot be performed) for 3 seconds or more.
(1 trip detection logic) |
No. 3 injector assembly | - | DTC stored |
| P168D | Injector #4 Internal EEPROM Malfunction | The EEPROM in the injector assembly is malfunctioning (EEPROM access (write or read) cannot be performed) for 3 seconds or more.
(1 trip detection logic) |
No. 4 injector assembly | - | DTC stored |
| DTC Detection Drive Pattern | Ignition switch ON for 3 minutes or more |
Refer to DTC P0201 (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>P0201).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and GTS on.
Clear the DTCs.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR
Turn the ignition switch off and wait for 30 seconds or more.
Turn the ignition switch to ON for 3 minutes or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P168A, P168B, P168C and/or P168D is output | A |
| No DTC is output | B |
A
B
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>CHECK FOR INTERMITTENT PROBLEMS
Replace the injector assembly of the cylinder relevant to the DTC.
Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL INJECTOR(w/ Glow Plug Controller)>REMOVAL
When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SYSTEM(w/ Glow Plug Controller)>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTC.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR
Turn the ignition switch off and wait for 30 seconds or more.
Turn the ignition switch to ON for 3 minutes or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT