Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052110 ECD SYSTEM(for i-ART) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P2564  Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low  P2565  Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit High  


DESCRIPTION

The variable nozzle vane type turbocharger consists primarily of a compressor wheel, turbine wheel, nozzle vane, unison ring, DC motor and nozzle vane position sensor.

The nozzle vane position sensor consists of a Hall IC and a magnetic yoke that rotates in unison with the movement of the linkage that actuates the nozzle vane. The nozzle vane position sensor converts the changes in the magnetic flux that are caused by the rotation of the DC motor (hence, the rotation of the magnetic yoke) into electric signals, and outputs them to the ECM. The ECM determines the actual nozzle vane position from the electric signals in order to calculate the target nozzle vane position.

A221597E09
4.219,1.552 4.229,0.656 4.229,0.656 4.521,0.656 false 1.375,3.073 1.5,3.313 true 1.063,2.292 0.667,1.219 0.667,1.219 0.792,1.219 true 1.365,1.74 1.5,1.188 1.5,1.188 1.615,1.188 true 0.5,3.875 2.594,4.365 2.094,0.49 10 false Nozzle Vane Position Sensor (Turbocharger Sub-assembly) 0.844,1.125 1.438,1.292 0.594,0.167 10 false Hall IC 2.323,2.479 2.813,2.677 0.49,0.198 10 false VTA1 2.99,3.146 3.521,3.344 0.531,0.198 10 false VNE2 2.99,1.573 3.552,1.771 0.563,0.198 10 false VNVC 3.073,3.552 3.458,3.771 0.385,0.219 10 false ECM 4.719,3.594 5.229,3.771 0.51,0.177 10 false Closed 5.76,3.583 6.344,3.76 0.583,0.177 10 false Opened 1.677,1.115 2.313,1.313 0.635,0.198 10 false Magnet 4.604,0.542 6.49,0.979 1.885,0.438 10 false Nozzle Vane Position Sensor Output Voltage (V) 0.063,2.688 0.531,3.073 0.469,0.385 10 false Sensor Vane 4.104,1.646 4.448,1.844 0.344,0.198 10 false 4.5 4.104,2.531 4.375,2.708 0.271,0.177 10 false 0.5 1.458,3.344 2.031,3.563 0.573,0.219 10 false Magnet 4.781,3.24 6.177,3.438 1.396,0.198 10 true Nozzle Vane Position 2.323,1.688 2.781,1.865 0.458,0.177 10 false VNVC 2.99,2.365 3.49,2.563 0.5,0.198 10 false VNA 2.323,3.25 2.927,3.5 0.604,0.25 10 false VNE2

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2564 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low VNA voltage is 0.1 V or less for 2.1 seconds (1 trip detection logic).
·

Nozzle vane position sensor (turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

ECM


Comes on DTC stored
P2565 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit High VNA voltage is 4.9 V or higher for 2.1 seconds (1 trip detection logic).
·

Nozzle vane position sensor (turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

ECM


Comes on DTC stored

HINT:

If DTC P2564 and/or P2565 is stored due to the nozzle vane being stuck open, the following symptoms may appear:

- Lack of power

- Vehicle surge or hesitation under light or medium load



CONFIRMATION DRIVING PATTERN

P2564, P2565
DTC Detection Drive Pattern Ignition switch ON for 1 second

WIRING DIAGRAM

A221590E14
0.74,2.875 2.653,3.059 1.913,0.184 10 Nozzle Vane Position Sensor 0.74,2.693 1.059,2.874 0.319,0.180 10 C40 5.833,2.707 6.239,2.877 0.406,0.170 10 C167 5.833,2.889 6.239,3.045 0.406,0.156 10 ECM 5.469,0.928 5.876,1.110 0.408,0.182 10 VNVC 5.469,1.418 5.861,1.609 0.392,0.191 10 VNA 5.469,1.867 5.888,2.037 0.420,0.170 10 VNE2 5.227,0.921 5.400,1.077 0.173,0.156 10 17 5.219,1.404 5.412,1.557 0.193,0.152 10 11 5.276,1.86 5.434,2.002 0.158,0.142 10 5 1.675,1.005 2.095,1.161 0.420,0.156 10 VNVC 1.724,1.495 2.096,1.644 0.371,0.149 10 VTA1 1.689,1.944 2.088,2.107 0.399,0.163 10 VNE2 2.194,0.921 2.295,1.077 0.101,0.156 10 3 2.194,1.397 2.295,1.553 0.101,0.156 10 1 2.194,1.86 2.295,2.016 0.101,0.156 10 2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2564 AND P2565)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
P2564 and/or P2565 is output A
P2564 and/or P2565 and other DTCs are output B




A

2.CHECK HARNESS AND CONNECTOR (ECM - NOZZLE VANE POSITION SENSOR)

B

2.CHECK HARNESS AND CONNECTOR (ECM - NOZZLE VANE POSITION SENSOR)
a.

Disconnect the nozzle vane position sensor connector.


b.

Disconnect the ECM.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C40-1 (VTA1) - C167-11 (VNA) Always Below 1 Ω
C40-2 (VNE2) - C167-5 (VNE2) Always Below 1 Ω
C40-3 (VNVC) - C167-17 (VNVC) Always Below 1 Ω
C40-1 (VTA1) or C167-11 (VNA) - Body ground Always 10 kΩ or higher
C40-3 (VNVC) or C167-17 (VNVC) - Body ground Always 10 kΩ or higher



d.

Reconnect the nozzle vane position sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (VNVC VOLTAGE)

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.INSPECT ECM (VNVC VOLTAGE)
a.
A302635C16
1.854,0.24 2.292,0.5 0.438,0.26 1.396,1.646 1.927,0.865 true 2.448,1.656 1.927,0.729 true 0.146,0.073 0.344,0.271 0.198,0.198 10 false *a 1.906,0.281 2.417,0.563 0.51,0.281 10 false C167 1.26,1.708 2.031,1.917 0.771,0.208 10 false 17 (VNVC) 2.406,1.708 3.177,1.917 0.771,0.208 10 false 5 (VNE2)
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C167-17 (VNVC) - C167-5 (VNE2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.REPLACE TURBOCHARGER SUB-ASSEMBLY (NOZZLE VANE POSITION SENSOR)

NG

7.REPLACE ECM
4.REPLACE TURBOCHARGER SUB-ASSEMBLY (NOZZLE VANE POSITION SENSOR)

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off.


d.

Turn the ignition switch off and wait for 30 seconds or more.


e.

Turn the ignition switch to ON and wait for 10 seconds or more.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P2564 and/or P2565.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, idle the engine.



Result:
Proceed to
NEXT



NEXT

END

7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED