Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052110 ECD SYSTEM(for i-ART) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  U0101  Lost Communication with TCM  


DESCRIPTION

The ECM (engine control unit) communicates with the TCM (transmission control ECU) through the Controller Area Network (CAN).

If there is a problem with this communication, the ECM stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
U0101 Lost Communication with TCM Both conditions are met for 1.25 seconds (1 trip detection logic):
·

The battery voltage is 10.5 V or higher.

·

No communication between the ECM and TCM.


·

ECM

·

TCM

·

ECM to TCM circuit


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

U0101
DTC Detection Drive Pattern Ignition switch ON for 3 seconds

WIRING DIAGRAM

A279711E02
0.885,2.844 1.438,3.042 0.552,0.198 10 false Battery 5.792,3.5 6.26,3.698 0.469,0.198 10 false TCM 5.594,3.021 5.99,3.198 0.396,0.177 10 false E1 5.583,0.729 6.073,0.927 0.49,0.198 10 false BATT 5.333,0.563 5.542,0.76 0.208,0.198 10 false 5 5.323,2.844 5.635,3.042 0.313,0.198 10 false 1 5.583,1.969 6.094,2.156 0.51,0.188 10 false CAN+ 5.302,1.802 5.635,2 0.333,0.198 10 false 21 5.583,2.479 6.146,2.688 0.563,0.208 10 false CAN- 5.292,2.313 5.583,2.51 0.292,0.198 10 false 20 3.135,1.969 3.573,2.167 0.438,0.198 10 false CAN+ 3.604,2.073 3.917,2.26 0.313,0.188 10 false 24 3.156,2.469 3.594,2.667 0.438,0.198 10 false CAN- 3.604,2.594 3.938,2.792 0.333,0.198 10 false 18 3,3.063 3.396,3.26 0.396,0.198 10 false ECM 2.99,2.885 3.438,3.083 0.448,0.198 10 false C163 5.24,0.74 5.625,0.917 0.385,0.177 10 false G41 5.25,2.49 5.635,2.698 0.385,0.208 10 false G41 5.24,1.969 5.698,2.146 0.458,0.177 10 false G41 5.25,3.01 5.573,3.188 0.323,0.177 10 false C24 1.021,0.885 1.667,1.083 0.646,0.198 10 false BATT P/I 2.177,0.75 2.458,0.948 0.281,0.198 10 false 1H 2.896,0.604 3.177,0.802 0.281,0.198 10 false EFI 3.677,0.74 3.948,0.979 0.271,0.24 10 false 1J 2.219,0.563 2.417,0.74 0.198,0.177 10 false 1 2.833,0.865 3.031,1.073 0.198,0.208 10 false 1 3.708,0.563 3.927,0.76 0.219,0.198 10 false 1 3.094,0.865 3.354,1.063 0.26,0.198 10 false 2 2.219,1.219 3.875,1.417 1.656,0.198 10 false No. 1 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC U0101)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
U0101 is output A
U0101 and other DTCs are output B


HINT:

If any DTCs other than U0101 are output, troubleshoot those DTCs first.




A

2.INSPECT TCM POWER SOURCE CIRCUIT (POWER SOURCE AND BODY GROUND)

B

2.INSPECT TCM POWER SOURCE CIRCUIT (POWER SOURCE AND BODY GROUND)
a.

Disconnect the TCM connector.


b.
C216560C05
0.781,0.354 1.167,0.615 0.385,0.26 2.167,0.365 2.552,0.625 0.385,0.26 2.125,2.708 2.281,1.969 true 1.396,2.729 1.302,1.958 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 0.854,0.406 1.167,0.604 0.313,0.198 10 false C24 2.24,0.417 2.552,0.615 0.313,0.198 10 false G41 1.781,2.74 2.344,2.938 0.563,0.198 10 false 5 (BATT) 1.198,2.75 1.667,2.927 0.469,0.177 10 false 1 (E1)
*1 Rear view of wire harness connector
(to TCM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G41-5 (BATT) - C24-1 (E1) Ignition switch ON 11 to 14 V



c.

Reconnect the TCM connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - TCM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ECM - TCM)
a.

Disconnect the TCM connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C163-24 (CAN+) - G41-21 (CAN+) Always Below 1 Ω
C163-18 (CAN-) - G41-20 (CAN-) Always Below 1 Ω
C163-24 (CAN+) or G41-21 (CAN+) - Body ground or other terminals Always 1 MΩ or higher
C163-18 (CAN-) or G41-20 (CAN-) - Body ground or other terminals Always 1 MΩ or higher



d.

Reconnect the TCM connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC U0101)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC U0101)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
No DTC is output A
U0101 is output B




A

END

B