Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(w/ EGR Cooler) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052067 ECD SYSTEM(w/ EGR Cooler) C

2KD-FTV ENGINE CONTROL  ECD SYSTEM(w/ EGR Cooler)  P245C  EGR Cooler Bypass Control Circuit Low  P245D  EGR Cooler Bypass Control Circuit High  


DESCRIPTION

The vacuum switching valve (for EGR bypass valve) is controlled by the ECM, and the opening and closing of the EGR cooler bypass valve is performed according to the vacuum applied by the vacuum pump.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P245C EGR Cooler Bypass Control Circuit Low Open or short in the vacuum switching valve (for EGR bypass valve) for 3 seconds (1 trip detection logic).
·

Open or short in vacuum switching valve (for EGR bypass valve) circuit

·

Vacuum switching valve (for EGR bypass valve)

·

ECM


Comes on DTC stored
P245D EGR Cooler Bypass Control Circuit High Open or short in the vacuum switching valve (for EGR bypass valve) for 3 seconds (1 trip detection logic).
·

Open or short in vacuum switching valve (for EGR bypass valve) circuit

·

Vacuum switching valve (for EGR bypass valve)

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

P245C, P245D
DTC Detection Drive Pattern Ignition switch to ON for 3 seconds

WIRING DIAGRAM

A155670
2.094,1.865 2.573,2.042 0.479,0.177 10 false MAIN 5.854,2.281 6.396,2.5 0.542,0.219 10 false MREL 5.865,1.146 6.406,1.365 0.542,0.219 10 false ECBV 6.146,0.292 6.563,0.5 0.417,0.208 10 false ECM 5.875,2.771 6.125,2.938 0.25,0.167 10 false E1 3.625,0.635 5.323,0.927 1.698,0.292 10 false VSV for No. 2 EGR Valve 1.865,2.844 3.698,3.104 1.833,0.26 10 false No. 1 Integration Relay 1.354,0.979 1.635,1.146 0.281,0.167 10 false EFI 0.146,2.104 1.052,2.49 0.906,0.385 10 false from BATT P/I Fuse 5.51,2.281 5.802,2.5 0.292,0.219 10 false G39 5.5,1.156 5.771,1.375 0.271,0.219 10 false C23 5.521,2.771 5.792,2.938 0.271,0.167 10 false C23 5.583,2.094 5.833,2.313 0.25,0.219 10 false 8 5.573,0.958 5.844,1.177 0.271,0.219 10 false 19 5.594,2.583 5.844,2.75 0.25,0.167 10 false 7 3.083,2.281 3.333,2.5 0.25,0.219 10 false 1J 3.083,1.146 3.354,1.365 0.271,0.219 10 false 1J 3.135,2.094 3.385,2.313 0.25,0.219 10 false 2 3.135,0.958 3.406,1.177 0.271,0.219 10 false 5 3.625,0.469 4.031,0.635 0.406,0.167 10 false C100 0.802,1.146 1.073,1.365 0.271,0.219 10 false 1H 0.854,0.969 1.125,1.188 0.271,0.219 10 false 1 4.771,0.99 4.938,1.167 0.167,0.177 10 false 2 4,1 4.167,1.219 0.167,0.219 10 false 1 4.24,2.021 4.76,2.302 0.521,0.281 10 false Diode 4.24,1.854 4.615,2.073 0.375,0.219 10 false C101 4.677,1.552 4.844,1.729 0.167,0.177 10 false 1 4.094,1.542 4.198,1.708 0.104,0.167 10 false 2 1.302,1.26 1.448,1.479 0.146,0.219 10 false 1 1.542,1.26 1.677,1.479 0.135,0.219 10 false 2 1.448,2.781 1.698,3 0.25,0.219 10 false 1J 1.208,2.792 1.479,3.01 0.271,0.219 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.INSPECT VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE)
a.

Inspect the vacuum switching valve (for EGR bypass valve).

Click hereEngine / Hybrid System>2KD-FTV EMISSION CONTROL>VACUUM SWITCHING VALVE(w/o DPF)>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE) (POWER SOURCE CIRCUIT)

NG

7.REPLACE VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE)
2.CHECK VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE) (POWER SOURCE CIRCUIT)
a.
A154589
0.813,1.271 1.281,1.573 0.469,0.302 0.125,0.125 0.396,0.302 0.271,0.177 10 false *a 0.865,1.344 1.271,1.521 0.406,0.177 10 false C100
*a Front view of wire harness connector
(to Vacuum Switching Valve (for EGR Bypass Valve))


Disconnect the vacuum switching valve (for EGR bypass valve) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C100-1 - Body ground Ignition switch to ON 11 to 14 V



c.

Reconnect the vacuum switching valve (for EGR bypass valve) connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE) - ECM)

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE) - ECM)
a.

Disconnect the vacuum switching valve (for EGR bypass valve) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C100-2 - C23-19 (ECBV) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C100-2 or C23-19 (ECBV) - Body ground Always 10 kΩ or higher



d.

Reconnect the vacuum switching valve (for EGR bypass valve) connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.

HINT:

If the voltage at the vacuum switching valve (for EGR bypass valve) connector is not 11 to 14 V, repair or replace the harness and connector between the vacuum switching valve (for EGR bypass valve) and EFI relay (including the EFI No. 2 fuse).



Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch to ON for 3 seconds.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.REPLACE VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE)
a.

Replace the vacuum switching valve (for EGR bypass valve).


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED