Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2013.10
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  VSC OFF Indicator Light Remains ON  


DESCRIPTION

Pressing the VSC OFF switch turns off traction control and pressing and holding this switch turns off traction control and VSC. If VSC turns off, the VSC OFF indicator light will come on.

When the transfer position is L4, VSC is prohibited and the VSC OFF indicator light turns on.

WIRING DIAGRAM

C237077
0.427,1.583 1.448,1.792 1.021,0.208 10 false from IG Circuit 0.438,4.365 1.448,4.563 1.01,0.198 10 false from IG Circuit 3.51,1.135 4.167,1.302 0.656,0.167 10 false VSC OFF 3.531,1.76 4.281,1.979 0.75,0.219 10 false TRC OFF 2.208,1.406 2.49,1.583 0.281,0.177 10 false 21 2.146,1.594 2.573,1.844 0.427,0.25 10 false G19 4.49,1.594 4.813,1.76 0.323,0.167 10 false G20 4.49,0.958 4.813,1.125 0.323,0.167 10 false G20 2.313,3.094 2.448,3.26 0.135,0.167 10 false 4 3.49,3.094 3.625,3.26 0.135,0.167 10 false 3 4.563,0.76 4.854,0.927 0.292,0.167 10 false 16 5.385,0.854 5.583,1.021 0.198,0.167 10 false 15 5.396,3.083 5.708,3.292 0.313,0.208 10 false 30 5.396,4.271 5.708,4.479 0.313,0.208 10 false 34 5.396,5.458 5.594,5.625 0.198,0.167 10 false 28 5.385,1.5 5.656,1.677 0.271,0.177 10 false 23 5.458,2.281 5.604,2.448 0.146,0.167 10 false 1 4.563,1.396 4.844,1.583 0.281,0.188 10 false 21 2.542,2.125 4.573,2.396 2.031,0.271 10 false Combination Meter Assembly 2.438,3.448 2.854,3.615 0.417,0.167 10 false G84 2.438,3.604 3.583,3.792 1.146,0.188 10 false VSC OFF Switch 5.427,6.094 5.844,6.26 0.417,0.167 10 false A36 5.427,6.25 7.042,6.667 1.615,0.417 10 false Skid Control ECU (Brake Actuator Assembly) 5.708,0.948 6.271,1.167 0.563,0.219 10 false VSCW 5.708,1.583 6.198,1.802 0.49,0.219 10 false INFR 5.708,5.563 6.125,5.729 0.417,0.167 10 false EXI3 5.708,3.167 6.125,3.333 0.417,0.167 10 false CSW 5.708,4.365 6.125,4.531 0.417,0.167 10 false IG1 5.708,2.385 6.198,2.573 0.49,0.188 10 false GND1 2.844,5.729 4.01,5.917 1.167,0.188 10 false ECU-IG&GAUGE 2.906,4.521 3.885,4.698 0.979,0.177 10 false ECU-IG NO. 2 2.521,1.479 2.813,1.646 0.292,0.167 10 false IG+ 4.031,0.854 4.458,1.021 0.427,0.167 10 false TROF 4.104,1.49 4.469,1.656 0.365,0.167 10 false TRC

CAUTION / NOTICE / HINT

NOTICE:
·

As there may be malfunctions in the transfer system related to when the transfer operates in L4, check the transfer system first (See page Drivetrain>VF2A TRANSFER / 4WD / AWD>TRANSFER SYSTEM>ON-VEHICLE INSPECTION).

·

After replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRC/VSC Off Mode VSC OFF switch Normal, Unknown, TRC OFF or VSC OFF Normal: Normal mode
TRC OFF: TRC off mode
VSC OFF: VSC off mode
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
TRC/VSC Off Mode
50003 105 282

f.

Check that the mode display changes according to VSC OFF switch operation.

OK:

The intelligent tester display changes according to VSC OFF switch operation.



Result:
Proceed to
OK
NG



OK

2.INSPECT BRAKE ACTUATOR ASSEMBLY

NG

3.INSPECT VSC OFF SWITCH
2.INSPECT BRAKE ACTUATOR ASSEMBLY
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Turn the ignition switch to ON.


d.

Check the state of the VSC OFF indicator light.


Result:
Result Proceed to
VSC OFF indicator light turns off A
VSC OFF indicator light does not turn off B



A

B

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)
3.INSPECT VSC OFF SWITCH
a.

Turn the ignition switch off.




Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)

NG

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
a.

Turn the ignition switch off.


b.

Disconnect the VSC OFF switch connector.


c.

Disconnect the skid control ECU (brake actuator assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-30 (CSW) - G84-3 Always Below 1 Ω
A36-30 (CSW) - Body ground Always 10 kΩ or higher
G84-4 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK TERMINAL VOLTAGE (EXI3 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (EXI3 TERMINAL)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the G20 combination meter connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-15 (VSCW) - G20-16 (TROF) Always Below 1 Ω
A36-15 (VSCW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR