Home › Brake › BRAKE (FRONT) › FRONT BRAKE(for 4WD and Pre-Runner) › from 2013.10
RM1840EF _54 Brake _009625 BRAKE (FRONT) _0052625 FRONT BRAKE(for 4WD and Pre-Runner) A

BRAKE (FRONT)  FRONT BRAKE(for 4WD and Pre-Runner)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT DISC

a.
C111383
2.135,1.115 2.135,0.188 2.135,0.188 1.115,0.188 true 2.115,1.26 1.948,1.26 1.948,1.26 1.948,0.188 true 0.906,0.104 1.083,0.271 0.177,0.167 10 false *1
*1 Matchmark


Align the matchmarks and install the disc.

HINT:

When replacing the disc with a new one, select the installation position where the disc has the smallest runout.



Hide 2.INSTALL DISC BRAKE CYLINDER ASSEMBLY LH

a.

Install the cylinder with the 2 bolts.

Torque:
122 N*m (1244 kgf*cm, 90 ft.*lbf)


Hide 3.CONNECT FRONT NO. 1 WHEEL CYLINDER TUBE LH

a.

Using a union nut wrench, connect the tube to the cylinder.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 4.INSTALL FRONT ANTI-SQUEAL SHIM KIT

C238121
0.936,2.119 1.085,2.262 0.149,0.142 10 *1 2.31,2.742 2.461,2.881 0.151,0.138 10 *1 1.051,0.195 1.201,0.338 0.149,0.142 10 *2 2.666,0.924 2.815,1.066 0.149,0.142 10 *2 0.548,3.015 0.698,3.157 0.149,0.142 10 *3 1.022,1.505 1.022,2.109 false 2.395,2.313 2.395,2.738 false 0.734,0.577 0.734,0.272 0.734,0.272 1.041,0.272 false 2.977,1.843 2.977,1.003 2.977,1.003 2.842,1.003 false
*1 No. 1 Anti-squeal Shim
*2 No. 2 Anti-squeal Shim
*3 Disc brake grease


a.

Apply disc brake grease to both sides of each No. 1 shim.


b.

Install the No. 1 and No. 2 shims to each pad.

NOTICE:
·

When replacing worn pads, the shims must be replaced together with the pads.

·

Install the shims in the correct position and direction.




Hide 5.INSTALL FRONT DISC BRAKE PAD

a.

Install the 2 disc brake pads to the cylinder.

NOTICE:

There should be no oil or grease on the friction surface of the pads and disc.



Hide 6.INSTALL FRONT DISC BRAKE ANTI-RATTLE SPRING

a.

for 15 inch Front Disc Brake (Type A):

i.

Install the anti-rattle spring.


ii.

Hold down the spring and insert the 2 pins.


iii.

Install the clip.



b.

for 15 inch Front Disc Brake (Type B):

i.

Install the 2 disc brake pad guide pins and pin hold clip.

HINT:

Install the spring together with the pin on the bottom side.



ii.

Install the clip.



c.

for 16 inch Front Disc Brake:

i.

Install the 2 pins and anti-rattle spring.

HINT:

Install the spring together with the pin on the bottom side.



ii.

Install the 2 clips.

NOTICE:

When installing the clip, be sure to install the clip with the handle facing the center of the vehicle.




d.

for 16 inch Front Disc Brake:

(for TDV, TASA Made)

i.

Install the anti-rattle spring.


ii.

Hold down the spring and insert the 2 pins.


iii.

Install the 2 clips.

NOTICE:

When installing the clip, be sure to install the clip with the handle facing the center of the vehicle.




Hide 12.BLEED CLUTCH LINE (for Manual Transmission)

Hide 13.INSTALL FRONT WHEEL

Torque:
105 N*m (1071 kgf*cm, 77 ft.*lbf)