Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2013.10
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052600 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

When one of the following conditions is met, the ABS warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

·

There is a malfunction in the skid control ECU (brake actuator assembly) internal circuit.

·

There is an open in the harness between the combination meter and the skid control ECU (brake actuator assembly).

·

The anti-lock brake system is defective.

·

The rear differential is locked.*

*: w/ Rear Differential Lock



WIRING DIAGRAM

C237785
5.948,0.479 6.344,0.76 0.396,0.281 10 false WA 5.948,1.104 6.406,1.323 0.458,0.219 10 false GND1 5.948,1.542 6.396,1.698 0.448,0.156 10 false GND2 5.958,2.177 6.417,2.406 0.458,0.229 10 false IG1 5.948,3.271 6.573,3.479 0.625,0.208 10 false EXI2 5.656,0.406 5.833,0.552 0.177,0.146 10 false 13 5.729,1.021 5.854,1.167 0.125,0.146 10 false 2 5.656,1.458 5.833,1.646 0.177,0.188 10 false 24 5.656,2.094 5.854,2.323 0.198,0.229 10 false 25 5.521,3.271 5.854,3.479 0.333,0.208 10 false 22*2 3.135,0.365 4.167,0.615 1.031,0.25 10 false Reverse Circuit 2.708,0.677 3.104,0.885 0.396,0.208 10 false ABS 4.646,0.302 4.844,0.458 0.198,0.156 10 false 38 1.906,0.313 2.125,0.51 0.219,0.198 10 false 21 4.604,0.5 4.917,0.698 0.313,0.198 10 false G19 2.521,1.688 4.406,1.948 1.885,0.26 10 false Combination Meter Assembly 0.542,0.469 1.552,0.708 1.01,0.24 10 false from IG Circuit 2.333,2.365 3.49,2.615 1.156,0.25 10 false ECU-IG NO. 2 0.542,2.177 1.531,2.354 0.99,0.177 10 false from IG Circuit 5.49,4.177 5.948,4.344 0.458,0.167 10 false A13 5.49,4.365 7.052,4.76 1.563,0.396 10 false Skid Control ECU (Brake Actuator Assembly) 1.656,2.76 2.646,2.938 0.99,0.177 10 false from IG Circuit 2.99,1.302 4.417,1.469 1.427,0.167 10 false Rear Differential Lock 2.677,3.552 2.969,3.771 0.292,0.219 10 false L8 2.677,3.708 4.875,4.167 2.198,0.458 10 false Rear Differential Position Switch (No. 4 Transfer Indicator Switch)*2 3.906,3.281 4.052,3.521 0.146,0.24 10 false 2 3.094,3.271 3.25,3.427 0.156,0.156 10 false 1 5.938,2.635 6.667,2.875 0.729,0.24 10 false EXI2 5.521,2.635 5.833,2.844 0.313,0.208 10 false 22*1 0.146,5.885 2.146,6.104 2,0.219 10 false *1: w/o Rear Differential Lock 0.146,6.208 2.781,6.427 2.635,0.219 10 false *2: w/ Rear Differential Lock 0.385,5.104 0.75,5.292 0.365,0.188 10 false K44 0.385,5.281 4.479,5.563 4.094,0.281 10 false Rear Differential Lock ECU (No. 2 4 Wheel Drive Control ECU)*2 2.063,4.531 2.396,4.698 0.333,0.167 10 false RLP 2.479,4.531 2.667,4.76 0.188,0.229 10 false 1 4.688,0.906 4.958,1.083 0.271,0.177 10 false 9*2 1.844,0.49 2.167,0.646 0.323,0.156 10 false G19 4.365,0.396 4.563,0.552 0.198,0.156 10 false LP 2.198,0.375 2.51,0.531 0.313,0.156 10 false IG+ 4.604,1.115 4.917,1.323 0.313,0.208 10 false G20 4.448,0.99 4.573,1.146 0.125,0.156 10 false L

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK FOR DTC
a.

Check if DTCs for the ABS are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 8
Result:
Result Proceed to
DTC not output A
DTC output B




A

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
a.
C117862
1.542,0.646 1.885,0.875 0.344,0.229 1.458,2.854 1.375,2.854 1.375,2.854 1.313,2.229 false 0.073,0.042 0.385,0.198 0.313,0.156 10 *a 1.594,0.688 2.073,0.979 0.479,0.292 10 A13 1.51,2.771 1.99,3.063 0.479,0.292 10 IG1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A13-25 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.
C117862
1.521,0.646 1.875,0.896 0.354,0.25 1.656,2.771 1.469,2.771 1.469,2.771 1.073,2.156 false 0.667,1.083 0.792,1.083 0.792,1.083 1.052,1.865 false 0.083,0.073 0.396,0.229 0.313,0.156 10 *a 1.583,0.698 2.094,1.042 0.51,0.344 10 A13 0.26,1 0.771,1.344 0.51,0.344 10 GND1 1.698,2.688 2.208,3.031 0.51,0.344 10 GND2
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-2 (GND1) - Body ground Always Below 1 Ω
A13-24 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the G19 combination meter connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-13 (WA) - G19-38 (LP) Always Below 1 Ω
A13-13 (WA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK TERMINAL VOLTAGE (EXI2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TERMINAL VOLTAGE (EXI2 TERMINAL)
a.
C117862
1.5,0.573 1.885,0.813 0.385,0.24 2.615,2.063 2.583,3 2.583,3 2.438,3 false 0.104,0.052 0.375,0.26 0.271,0.208 10 false *a 1.563,0.604 1.854,0.792 0.292,0.188 10 false A13 2.115,2.927 2.469,3.094 0.354,0.167 10 false EXI2
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A13-22 (EXI2) - Body ground Ignition switch ON 11 to 14 V


Result:
Result Proceed to
NG (w/ Rear Differential Lock) A
NG (w/o Rear Differential Lock) B
OK C




A

7.CHECK HARNESS AND CONNECTOR (EXI2 TERMINAL CIRCUIT)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

9.CHECK ABS WARNING LIGHT
7.CHECK HARNESS AND CONNECTOR (EXI2 TERMINAL CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the rear differential lock position switch (No. 4 transfer indicator switch) connector.


c.

Disconnect the rear differential lock ECU (No. 2 4 wheel drive control ECU) connector.


d.

Disconnect the skid control ECU (brake actuator assembly) connector.


e.

Disconnect the G20 combination meter connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-22 (EXI2) - L8-2 Always Below 1 Ω
A13-22 (EXI2) - G20-9 (L) Always Below 1 Ω
A13-22 (EXI2) - K44-1 (RLP) Always Below 1 Ω
A13-22 (EXI2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT REAR DIFFERENTIAL LOCK SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT REAR DIFFERENTIAL LOCK SYSTEM

Result:
Proceed to
OK
NG



OK

9.CHECK ABS WARNING LIGHT

NG

9.CHECK ABS WARNING LIGHT
a.
C117862
1.531,0.594 1.865,0.813 0.333,0.219 1.375,1.979 2.417,0.896 2.417,0.896 2.563,0.896 false 1.073,1.833 1.063,0.844 1.063,0.844 0.906,0.844 false 1.063,2.146 1.063,2.875 1.063,2.875 1.323,2.875 false 0.104,0.073 0.417,0.229 0.313,0.156 10 *a 1.573,0.625 2.063,0.938 0.49,0.313 10 A13 0.51,0.76 1,1.073 0.49,0.313 10 GND1 2.604,0.813 3.094,1.125 0.49,0.313 10 WA 1.365,2.781 1.854,3.094 0.49,0.313 10 GND2
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Using SST, connect terminals 13 (WA) and 2 (GND1) or 24 (GND2) of the skid control ECU (brake actuator assembly) connector.


SST
09843-18040  

d.

Turn the ignition switch to ON.


e.

Check the ABS warning light.

OK:

ABS warning light turns off.



Result:
Proceed to
OK
NG



OK

NG

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)