This DTC is stored if the radio and display receiver assembly judges as a result of its self check that the signals or signal lines between the radio and display receiver assembly and the rear television camera assembly are not normal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1622 | Open or Short Circuit in Back Camera Signal | Open or Short Circuit in rear television camera signal | ·
Harness or connector ·
Rear television camera assembly ·
Radio and display receiver assembly |
| Proceed to |
|---|
| No DTC is output |
| DTC is output |
No DTC is output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
DTC is output
Disconnect the G158 radio and display receiver assembly connector.
Disconnect the M2 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G158-11 (CA+) - M2-4 (CB+) | Always | Below 1 Ω |
| G158-12 (V+) - M2-2 (CV+) | Always | Below 1 Ω |
| G158-23 (CGND) - M2-3 (CGND) | Always | Below 1 Ω |
| G158-24 (V-) - M2-1 (CV-) | Always | Below 1 Ω |
| G158-11 (CA+) - Body ground | Always | 10 kΩ or higher |
| G158-12 (V+) - Body ground | Always | 10 kΩ or higher |
| G158-23 (CGND) - Body ground | Always | 10 kΩ or higher |
| G158-24 (V-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Radio and Display Receiver Assembly) |
Disconnect the G158 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G158-23 (CGND) - Body ground | Always | Below 1 Ω |
| G158-24 (V-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Rear Television Camera Assembly) |
Disconnect the M2 rear television camera assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M2-4 (CB+) - M2-3 (CGND) | Ignition switch ACC | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using an oscilloscope, check the waveform
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
*b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronized Signal |
| *e | Video Waveform | - | - |
| Item | Content |
|---|---|
| Tester Connection | G158-12 (V+) - G158-24 (V-) |
| Tool Setting | 0.2 V/DIV., 50 μs/DIV. |
| Condition | Waveform 1: Ignition switch ON, shift lever in R
Waveform 2: Ignition switch ON, shift lever in R, screen blacked out by covering camera lens |
Waveform is as shown in illustration.
The video waveform changes according to the image sent by the rear television camera assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Replace the rear television camera assembly with a new or normally functioning one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| No DTC is output |
| DTC is output |
No DTC is output
DTC is output