Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM(for Navigation Receiver Type) › from 2013.10
RM1840EF _56 Audio / Visual / Telematics _009633 PARK ASSIST / MONITORING _0052664 REAR VIEW MONITOR SYSTEM(for Navigation Receiver Type) C

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM(for Navigation Receiver Type)  C1622  Open or Short Circuit in Back Camera Signal  


DESCRIPTION

This DTC is stored if the navigation receiver assembly judges as a result of its self check that the signals or signal lines between the navigation receiver assembly and the rear television camera assembly are not normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1622 Open or Short Circuit in Back Camera Signal Open or Short Circuit in rear television camera signal
·

Harness or connector

·

Rear television camera assembly

·

Navigation receiver assembly



WIRING DIAGRAM

E275627
5.594,2.802 6.208,3 0.615,0.198 10 false G159 5.594,2.979 6.969,3.417 1.375,0.438 10 false Navigation Receiver Assembly 5.729,1 6.344,1.198 0.615,0.198 10 false CA+ 5.74,1.458 6.354,1.656 0.615,0.198 10 false V+ 5.75,1.958 6.365,2.156 0.615,0.198 10 false V- 5.74,2.375 6.354,2.573 0.615,0.198 10 false CGND 1.125,1.01 1.469,1.208 0.344,0.198 10 false CB+ 1.135,1.438 1.5,1.646 0.365,0.208 10 false CV+ 1.156,1.948 1.479,2.156 0.323,0.208 10 false CV- 1.021,2.375 1.479,2.583 0.458,0.208 10 false CGND 0.427,2.813 1.042,3.01 0.615,0.198 10 false M2 0.427,3.01 1.802,3.448 1.375,0.438 10 false Rear Television Camera Assembly 2.292,2.531 2.479,2.729 0.188,0.198 10 false * 3.125,2.531 3.313,2.729 0.188,0.198 10 false * 3.99,2.552 4.177,2.75 0.188,0.198 10 false * 4.833,2.542 5.021,2.74 0.188,0.198 10 false * 2.219,3.49 3.521,3.698 1.302,0.208 10 false *: Shielded 5.427,0.875 5.646,1.073 0.219,0.198 10 false 11 5.427,1.344 5.646,1.542 0.219,0.198 10 false 12 5.448,1.844 5.667,2.042 0.219,0.198 10 false 24 5.448,2.24 5.667,2.438 0.219,0.198 10 false 23 1.552,0.885 1.771,1.083 0.219,0.198 10 false 4 1.552,1.344 1.771,1.542 0.219,0.198 10 false 2 1.552,1.813 1.771,2.01 0.219,0.198 10 false 1 1.563,2.25 1.781,2.448 0.219,0.198 10 false 3

PROCEDURE

1.CHECK FOR DTC

A

B

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the G159 navigation receiver assembly connector.


b.

Disconnect the M2 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G159-11 (CA+) - M2-4 (CB+) Always Below 1 Ω
G159-12 (V+) - M2-2 (CV+) Always Below 1 Ω
G159-23 (CGND) - M2-3 (CGND) Always Below 1 Ω
G159-24 (V-) - M2-1 (CV-) Always Below 1 Ω
G159-11 (CA+) - Body ground Always 10 kΩ or higher
G159-12 (V+) - Body ground Always 10 kΩ or higher
G159-23 (CGND) - Body ground Always 10 kΩ or higher
G159-24 (V-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT NAVIGATION RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT NAVIGATION RECEIVER ASSEMBLY
a.
E275624
1.521,0.49 1.979,0.76 0.458,0.271 0.583,1.875 0.792,1.875 0.792,1.875 1.042,1.427 true 1.396,1.865 1.26,1.865 1.26,1.865 1.167,1.406 true 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 1.448,1.771 1.927,1.969 0.479,0.198 10 false CGND 0.365,1.771 0.646,1.958 0.281,0.188 10 false V- 1.573,0.552 2.052,0.75 0.479,0.198 10 false G159
*a Component without harness connected
(Navigation Receiver Assembly)


Disconnect the G159 navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G159-23 (CGND) - Body ground Always Below 1 Ω
G159-24 (V-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK NAVIGATION RECEIVER ASSEMBLY

NG

4.CHECK NAVIGATION RECEIVER ASSEMBLY
a.
E227664
1.5,0.25 1.927,0.521 0.427,0.271 1.833,1.406 2.292,1.708 2.292,1.708 2.49,1.708 true 1.563,1.406 1.115,1.708 1.115,1.708 0.917,1.708 true 1.625,0.302 1.917,0.49 0.292,0.188 10 false M2 0.042,0 0.271,0.167 0.229,0.167 10 false *a 2.552,1.625 2.865,1.792 0.313,0.167 10 false CB+ 0.479,1.625 0.917,1.792 0.438,0.167 10 false CGND
*a Front view of wire harness connector
(to Rear Television Camera Assembly)


Disconnect the M2 rear television camera assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M2-4 (CB+) - M2-3 (CGND) Ignition switch ACC 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

5.CHECK REAR TELEVISION CAMERA ASSEMBLY

NG

5.CHECK REAR TELEVISION CAMERA ASSEMBLY
a.

Using an oscilloscope, check the waveform

E275625
0.906,0.688 1.385,0.969 0.479,0.281 0.583,1.49 0.531,2.031 0.531,2.031 0.438,2.031 true 0.583,1.333 0.5,0.781 0.5,0.781 0.406,0.781 true 2.792,1.896 2.729,2.469 2.729,2.469 2.635,2.469 true 2.906,1.792 3.063,2.479 3.063,2.479 3.177,2.479 true 5.427,1.74 5.375,2.365 5.375,2.365 5.281,2.365 true 5.552,1.688 5.708,2.375 5.708,2.375 5.823,2.375 true 2.031,1.354 2.479,1.552 0.448,0.198 10 false GND 0.167,0.698 0.458,0.896 0.292,0.198 10 false V+ 0.24,1.948 0.51,2.135 0.271,0.188 10 false V- 0.073,0.083 0.521,0.281 0.448,0.198 10 false *a 4.625,1.365 5.073,1.563 0.448,0.198 10 false GND 2.24,0.354 2.688,0.552 0.448,0.198 10 false *b 1,0.771 1.448,0.969 0.448,0.198 10 false G159 4.854,0.354 5.302,0.552 0.448,0.198 10 false *c 2.427,2.375 2.875,2.573 0.448,0.198 10 false *d 3.26,2.406 3.708,2.604 0.448,0.198 10 false *e 5.083,2.281 5.531,2.479 0.448,0.198 10 false *d 5.865,2.302 6.313,2.5 0.448,0.198 10 false *e
*a Component with harness connected
(Navigation Receiver Assembly)
*b Waveform 1
*c Waveform 2 *d Synchronized Signal
*e Video Waveform - -


Measurement Condition
Item Content
Tester Connection G159-12 (V+) - G159-24 (V-)
Tool Setting 0.2 V/DIV., 50 μs/DIV.
Condition Waveform 1: Ignition switch ON, shift lever in R
Waveform 2: Ignition switch ON, shift lever in R, screen blacked out by covering camera lens

OK:

Waveform is as shown in illustration.


HINT:

The video waveform changes according to the image sent by the rear television camera assembly.



Result:
Proceed to
OK
NG



OK

NG

6.REPLACE REAR TELEVISION CAMERA ASSEMBLY
6.REPLACE REAR TELEVISION CAMERA ASSEMBLY
a.

Replace the rear television camera assembly with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC

A

END (REAR TELEVISION CAMERA ASSEMBLY WAS DEFECTIVE)

B