Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2013.10
RM1840EF _56 Audio / Visual / Telematics _009632 NAVIGATION / MULTI INFO DISPLAY _0052661 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15C2  Speed Signal Malfunction  


DESCRIPTION

The navigation receiver assembly receives a vehicle speed signal from the combination meter assembly and information from the navigation antenna assembly, and then adjusts the vehicle position.

The navigation receiver assembly stores this DTC when the difference between the speed information that the navigation antenna assembly receives and the SPD pulse received from the combination meter assembly becomes large.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly.

The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective systems based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



DTC No. Detection Item DTC Detection Condition Trouble Area
B15C2 Speed Signal Malfunction A difference between the GPS speed and SPD pulse is detected.
·

Meter/gauge system

·

Harness or connector

·

Navigation receiver assembly



WIRING DIAGRAM

E278018
0.979,1.979 2.896,2.198 1.917,0.219 10 false Combination Meter Assembly 1.792,1.052 2.25,1.25 0.458,0.198 10 false +S 2.073,0.927 2.531,1.125 0.458,0.198 10 false 6 5.198,1.052 5.656,1.25 0.458,0.198 10 false SPD 4.927,0.917 5.385,1.115 0.458,0.198 10 false 17 0.979,1.781 2.208,2.01 1.229,0.229 10 false G19 5.052,1.792 6.281,2.021 1.229,0.229 10 false G152 5.042,1.979 6.958,2.198 1.917,0.219 10 false Navigation Receiver Assembly

PROCEDURE

1.CHECK VEHICLE SENSOR (OPERATION CHECK)
a.
E276610

Enter the "System Sensors Check" screen. Refer to Check GPS & Vehicle Sensors in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

While driving the vehicle, compare the "Speed" indicator to the reading on the speedometer. Check if these readings are almost equal.


Result:
Proceed to
The readings are equal or almost equal
The readings are not equal or almost equal



The readings are equal or almost equal

The readings are not equal or almost equal

2.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
2.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E256135
1.479,0.438 1.896,0.656 0.417,0.219 2.458,2 2.188,1.365 true 0.167,0.198 0.479,0.396 0.313,0.198 10 false *a 1.552,0.469 1.865,0.667 0.313,0.198 10 false G19 2.396,2.042 2.708,2.24 0.313,0.198 10 false +S 2.792,3.594 3.188,3.865 0.396,0.271 10 false GND 1.073,3.875 1.469,4.146 0.396,0.271 10 false (A)
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


ii.

Connect an oscilloscope to terminal G19-6 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal G19-6 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


OK:

The waveform is similar to that shown in the illustration.




Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the G152 navigation receiver assembly connector.


b.

Disconnect the G19 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G152-17 (SPD) - G19-6 (+S) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR