Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2013.10
RM1840EF _56 Audio / Visual / Telematics _009632 NAVIGATION / MULTI INFO DISPLAY _0052661 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Radio Broadcast cannot be Received or Poor Reception  


WIRING DIAGRAM

E277657
6.063,1.198 6.677,1.396 0.615,0.198 10 false MAIN 6.052,1.469 6.667,1.667 0.615,0.198 10 false ANT+ 5.448,1.073 6.063,1.271 0.615,0.198 10 false 3 5.458,1.354 6.073,1.552 0.615,0.198 10 false 5 5.896,2.25 6.51,2.448 0.615,0.198 10 false RA 5.906,2.427 7.135,2.792 1.229,0.365 10 false Navigation Receiver Assembly 3.177,2.125 4.458,2.573 1.281,0.448 10 false No. 2 Antenna Cord Sub-assembly 4.781,2.135 5.729,2.583 0.948,0.448 10 false Antenna Cord Sub-assembly 0.854,0.615 2.031,0.979 1.177,0.365 10 false Roof Antenna Pole Sub-assembly 1.208,1.625 2.49,1.969 1.281,0.344 10 false Antenna with Holder Assembly

PROCEDURE

1.CHECK NAVIGATION RECEIVER ASSEMBLY
a.

Check the radio automatic station search function.

i.

Check the radio automatic station search function by activating it.



Result:
Proceed to
Automatic station search function does not stop
Automatic station search function stops on a station



Automatic station search function does not stop

2.CHECK OPTIONAL COMPONENTS

Automatic station search function stops on a station

2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

Result:
Proceed to
Optional components are not installed
Optional components are installed


NOTICE:

Do not remove optional components without the permission of the customer.




Optional components are not installed

3.CHECK NAVIGATION RECEIVER ASSEMBLY

Optional components are installed

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3.CHECK NAVIGATION RECEIVER ASSEMBLY
a.
E245523

Preparation for check

i.

Disconnect the antenna connector from the navigation receiver assembly.



b.

Check for noise

i.

Turn the ignition switch to ACC with the navigation receiver assembly connector connected.


ii.

Turn the radio on and tune into AM mode.


iii.

Place a screwdriver, thin wire or other metal object on the navigation receiver assembly antenna jack and check that noise can be heard from the speakers.



Result:
Proceed to
Noise can be heard from the speakers
Noise cannot be heard from the speakers



Noise can be heard from the speakers

4.INSPECT NAVIGATION RECEIVER ASSEMBLY

Noise cannot be heard from the speakers

4.INSPECT NAVIGATION RECEIVER ASSEMBLY
a.

Disconnect the navigation receiver assembly connector.


b.
E188455
1.521,1.094 1.115,1.448 false 0.802,1.469 1.198,1.635 0.396,0.167 10 false ANT+

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5 (ANT+) - Body ground Ignition switch ACC
Radio switch on and AM or FM selected
11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

5.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
E278669
0.51,0.854 0.875,1.083 0.365,0.229 1.583,1.208 1.094,1.375 true 2.552,0.792 2.063,0.958 true 0.167,0.104 0.479,0.26 0.313,0.156 10 false *a 0.219,1.885 0.531,2.042 0.313,0.156 10 false *b 0.594,0.875 0.906,1.031 0.313,0.156 10 false RA 0.74,1.396 1.406,1.615 0.667,0.219 10 false MAIN 2.594,0.719 3.26,0.938 0.667,0.219 10 false ANT+
*a Front view of wire harness connector
(to Navigation Receiver Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Disconnect the navigation receiver assembly connector.


b.

Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
RA-3 (MAIN) - 2 Always Below 1 Ω
RA-5 (ANT+) - 3 Always Below 1 Ω
RA-3 (MAIN) - Body ground Always 10 kΩ or higher
RA-5 (ANT+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E276821
0.188,0.094 0.5,0.25 0.313,0.156 10 false *a 0.281,1.875 0.594,2.031 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to Antenna with Holder Assembly)
*b Front view of wire harness connector
(to Antenna Cord Sub-assembly)


Disconnect the antenna connector from the antenna cord sub-assembly.


b.

Disconnect the antenna connector from the antenna with holder assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 2 Always Below 1 Ω
3 - 3 Always Below 1 Ω
2 - Body ground Always 10 kΩ or higher
3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

7.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY
a.

Check that the roof antenna pole sub-assembly is securely installed.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA POLE>REMOVAL


Result:
Proceed to
The roof antenna pole sub-assembly is installed properly
The roof antenna pole sub-assembly is not installed properly



The roof antenna pole sub-assembly is installed properly

8.CHECK ANTENNA WITH HOLDER ASSEMBLY

The roof antenna pole sub-assembly is not installed properly

CHECK AND REPLACE ROOF ANTENNA POLE SUB-ASSEMBLY

8.CHECK ANTENNA WITH HOLDER ASSEMBLY
a.

Replace the antenna with holder assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL


b.

Check if radio broadcasts can be received normally.


Result:
Proceed to
Radio broadcasts can be received normally
Radio broadcasts cannot be received normally



Radio broadcasts can be received normally

END (ANTENNA WITH HOLDER ASSEMBLY IS DEFECTIVE)

Radio broadcasts cannot be received normally