Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.
| Proceed to |
|---|
| Optional components are not installed |
| Optional components are installed |
Do not remove optional components without the permission of the customer.
Optional components are not installed
Optional components are installed
| *1 | Tester Probe |
| *2 | Tin Foil |
| *3 | Antenna Wire |
Check for continuity in the antenna.
Check for continuity at the center of each antenna wire as shown in the illustration.
When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of each probe and press the foil against the wire with your finger as shown in the illustration.
| Proceed to |
|---|
| There is continuity in the antenna wire |
| There is not continuity in the antenna wire |
There is continuity in the antenna wire
There is not continuity in the antenna wire
Enter the "DTV reception check" screen. Refer to Check Digital Television Reception in Operation Check.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK
As digital TV is a terrestrial broadcast, the digital TV antenna cannot receive the signal in places where the signal may not reach the vehicle, such as mountains or tunnels.
Even in areas where digital TV broadcasts for households can be received, the in-vehicle digital TV may not be able to receive the broadcast.
Check the digital TV tuner reception level.
Do not depend solely on the reception level as a reference value as it may vary depending on the signal conditions such as wave interference.
If the result changes after turning around the vehicle, it is not a malfunction, but is caused by a local weak electric field.
Digital TV tuner reception level check result indicates good reception.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front wire of wire harness connector
(to Navigation Receiver Assembly) |
| *b | Front wire of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
Disconnect the navigation receiver assembly connector.
Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (DTV) - 1 | Always | Below 1 Ω |
| 1-a - 1-b | Always | Below 1 Ω |
| 1 (DTV) - Body ground | Always | 10 kΩ or higher |
| 1-a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front wire of wire harness connector
(to Windshield Glass [Digital TV Antenna]) |
| *b | Front wire of wire harness connector
(to Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the antenna cord sub-assembly.
Disconnect the antenna connector from the windshield glass (digital TV antenna).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 1 | Always | Below 1 Ω |
| 1-b - 1-c | Always | Below 1 Ω |
| 1 - Body ground | Always | 10 kΩ or higher |
| 1-b - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the windshield glass (digital TV antenna) with a new or normally functioning one.
Click hereVehicle Exterior>WINDOW / GLASS>WINDSHIELD GLASS>REMOVAL
Check if the same problem occurs again.
| Proceed to |
|---|
| Malfunction disappears |
| Malfunction does not disappears |
Malfunction disappears
Malfunction does not disappears