This DTC is stored when a malfunction occurs in the television antenna assembly which is connected to the radio receiver assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C8 | Digital TV Antenna 1 Disconnected | Television antenna assembly is not connected. | ·
Antenna cord sub-assembly ·
No. 2 antenna cord sub-assembly ·
Windshield glass (digital TV antenna) ·
Navigation receiver assembly |
Clear the DTCs.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
| Proceed to |
|---|
| No DTCs are output |
| DTCs are output |
No DTCs are output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
DTCs are output
| *a | Front wire of wire harness connector
(to Navigation Receiver Assembly) |
| *b | Front wire of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
Disconnect the navigation receiver assembly connector.
Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (DTV) - 1 | Always | Below 1 Ω |
| 1-a - 1-b | Always | Below 1 Ω |
| 1 (DTV) - Body ground | Always | 10 kΩ or higher |
| 1-a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front wire of wire harness connector
(to Windshield Glass [Digital TV Antenna]) |
| *b | Front wire of wire harness connector
(to Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the antenna cord sub-assembly.
Disconnect the antenna connector from the windshield glass (digital TV antenna).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 1 | Always | Below 1 Ω |
| 1-b - 1-c | Always | Below 1 Ω |
| 1 - Body ground | Always | 10 kΩ or higher |
| 1-b - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Tester Probe |
| *2 | Tin Foil |
| *3 | Antenna Wire |
Check for continuity in the antenna.
Check for continuity at the center of each antenna wire as shown in the illustration.
When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of each probe and press the foil against the wire with your finger as shown in the illustration.
| Proceed to |
|---|
| There is continuity in the antenna wire |
| There is not continuity in the antenna wire |
There is continuity in the antenna wire
There is not continuity in the antenna wire
Replace the windshield glass (digital TV antenna) with a known good one and check if the same DTC is output again.
Click hereVehicle Exterior>WINDOW / GLASS>WINDSHIELD GLASS>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check if the same DTC is output again.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| OK |
| NG |
OK
NG