Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2013.10
RM1840EF _56 Audio / Visual / Telematics _009631 AUDIO / VIDEO _0052657 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) Y

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:

Use these procedures to troubleshoot the audio and visual system.


PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
·

When troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points in problem analysis:

What Vehicle model, system name
When Date, time, occurrence frequency
Where Road conditions
Under what conditions? Driving conditions, weather conditions
How did it happen? Problem symptoms


Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage with the ignition switch off.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery.


Result:
Proceed to
NEXT



NEXT

4.CHECK CABIN
4.CHECK CABIN
a.

Check that condensation is not likely to occur in the cabin, and that the temperature is not high or extremely low in the cabin.

OK:

Condensation is not likely being produced and the temperature is not high or extremely low.


HINT:
·

A humid cabin and a rapid change in temperature may lead to condensation. Condensation in the cabin may cause a short circuit.

·

The audio and visual system may not operate normally when the temperature is -20°C (-4°F) or less, or 65°C (149°F) or higher.




Result:
Procced to
OK
NG



OK

5.CHECK FOR DTC

NG

SET CABIN TO APPROPRIATE TEMPERATURE

5.CHECK FOR DTC

b.

Clear the DTCs.


c.

Recheck for DTCs by simulating the operation indicated by the DTCs.


Result:
Result Proceed to
DTC is not output A
DTC is output B



A

6.PROBLEM SYMPTOMS TABLE

B

6.PROBLEM SYMPTOMS TABLE
a.

Refer to Problem Symptoms Table.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in problem symptoms table A
Fault is listed in problem symptoms table B


HINT:

If the symptom does not recur and no DTC is output, perform the symptom simulation method.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING




A

7.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM

B

8.ADJUST, REPAIR OR REPLACE
7.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM

NEXT

8.ADJUST, REPAIR OR REPLACE
8.ADJUST, REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DIAGNOSTIC TROUBLE CODE
9.CHECK FOR DIAGNOSTIC TROUBLE CODE
HINT:

After clearing DTCs, recheck for DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR


Result:
Proceed to
NEXT



NEXT

10.PERFORM CONFIRMATION TEST
10.PERFORM CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END