Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2013.10
RM1840EF _56 Audio / Visual / Telematics _009631 AUDIO / VIDEO _0052657 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) D

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  DTC CHECK / CLEAR  


START DIAGNOSTIC MODE


HINT:
·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

·

If the system cannot enter the diagnostic mode, replace the radio and display receiver assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL

·

Start diagnostic mode at least 15 seconds after turning the ignition switch to ON. Otherwise, some items cannot be checked.



a.

Turn the ignition switch to ON.


b.
E276991

While pressing and holding the "AUDIO" switch, operate the headlight dimmer switch assembly: off → turn on → turn off → turn on → turn off → turn on → turn off.


c.

Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.



FAILURE DIAGNOSIS


a.
E278177

The "Failure Diagnosis" screen will be displayed by pressing the "Failure Diagnosis" switch on the "Service Menu" screen.



SYSTEM CHECK


a.
E278178

The "System Check Mode" screen will be displayed by pressing the "System Check" switch on the "Failure Diagnosis" screen.



CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN)


a.
E278179
0.25,1 0.417,1 0.417,1 0.552,0.833 false 0.854,1 1.021,1 1.021,1 1.156,0.833 false 2.5,0.833 2.302,0.833 2.302,0.833 2.302,1 false 1.75,1.979 1.917,1.979 1.917,1.979 2.052,1.813 false 2.333,1.969 2.5,1.969 2.5,1.969 2.635,1.802 false 0.083,0.896 0.396,1.094 0.313,0.198 10 false *a 0.677,0.917 0.99,1.115 0.313,0.198 10 false *b 2.521,0.74 2.833,0.938 0.313,0.198 10 false *e 1.594,1.896 1.906,2.094 0.313,0.198 10 false *c 2.167,1.885 2.479,2.083 0.313,0.198 10 false *d

System check mode screen description

Screen Description
Display Content
*a: Device Name List No. 1
·

Device Name List No. 1 displays some of the devices that make up the audio and visual system

·

The names of the components from Device Name List No. 1 are shown in the following table


*b: Check Result Result codes for all devices are displayed
*c: Memory Clear
·

Present and history DTCs and registered connected device names are cleared

·

Press the "Memory CLR" switch for 3 seconds


*d: Recheck
·

A system check will be performed again after the memory is cleared

·

The "Recheck" switch will dim during a system check


*e: Device Name List No. 2
·

Device Name List No. 2 displays some of the devices that make up the audio and visual system

·

The names of the components from Device Name List No. 2 are shown in the following table



*a: Device Name List No. 1 Description
Name Component Connection Method
DA Radio and display receiver assembly -

*b: Check Result Description
Result Meaning Action
OK The device does not respond with a DTC -
DETAIL The device responds with a DTC Look up the DTC in "Unit Check Mode"
NCON The device was previously present, but does not respond in diagnostic mode Check power supply wire harness of the device
NRES The device responds in diagnostic mode, but gives no DTC information Check power supply wire harness of the device

*e: Device Name List No. 2 Description
Result Meaning Action
AUX/VTR No. 1 stereo jack adapter assembly Vehicle wire harness


b.
E278180
0.333,0.917 0.667,0.917 false 0.344,0.677 0.677,0.677 false 0.854,0.167 1.052,0.167 1.052,0.167 1.333,0.615 true 1.708,0.167 1.542,0.167 1.542,0.167 1.458,0.417 true 2.01,1.021 2.177,1.25 2.177,1.25 2.344,1.25 false 2.625,1.75 2.792,1.979 2.792,1.979 2.958,1.979 false 0.156,0.833 0.469,1.031 0.313,0.198 10 false *d 0.156,0.583 0.469,0.781 0.313,0.198 10 false *c 0.677,0.083 0.99,0.281 0.313,0.198 10 false *b 1.74,0.073 2.052,0.271 0.313,0.198 10 false *a 2.396,1.167 2.708,1.365 0.313,0.198 10 false *e 3,1.885 3.313,2.083 0.313,0.198 10 false *f

Unit check mode screen description

Screen Description
Display Content
*a: Device name Target device
*b: History DTC Diagnostic memory results and stored DTCs are displayed
*c: Current DTC DTCs output in the service check are displayed.
*d: DTC DTC (Diagnostic Trouble Code)
*e: Timestamp The time and date of history DTCs are displayed. (The year is displayed in 2-digit format.)
*f: Diagnosis clear switch Pushing this switch for 3 seconds clears the diagnostic memory data of the target device (Both response to diagnostic system check result and the displayed data are cleared)

HINT:
·

This screen is updated once per second.

·

A maximum of 6 DTCs can be displayed for history and present DTCs.




c.
E278181

Read the system check result.

i.

If the check result is "DETAIL", touch the displayed check result to view the results on the "Unit Check Mode" screen and record them.

NOTICE:

A maximum of 6 DTCs can be displayed for history and present DTCs on the "Unit check mode" screen. Therefore, when 6 DTCs are displayed, troubleshoot those DTCs first and then check the "Unit check mode" screen again to see if any other DTCs are displayed.


HINT:
·

When all results are "OK", this means that no DTCs are output.

·

When proceeding to view the results of another device, press the "Back" switch to return to the "System Check Mode" screen. Repeat the step above to view the results of other devices.




ii.

Check the details of the DTC(s).

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DIAGNOSTIC TROUBLE CODE CHART

NOTICE:

The audio and visual system outputs DTCs for the following system. When DTCs other than those in Diagnostic Trouble Code Chart for the audio and visual system are output, refer to Diagnostic Trouble Code Chart for the relevant system.





DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN)


a.

Clear DTCs

i.
E278182

Press the "Memory CLR" switch for 3 seconds.


ii.

Confirm that the check results are cleared.

HINT:
·

To clear the DTCs for a specific device, clear the DTCs using the "Unit Check Mode" screen.

·

When clearing the DTCs using the "Unit Check Mode" screen, press the "Code CLR" switch for 3 seconds.





b.

Recheck

i.
E278183

Press the "Recheck" switch.


ii.
E278185

Confirm that all diagnostic codes are "OK" when the check results are displayed. If a code other than "OK" is displayed, troubleshoot again.

HINT:

When the DTCs are cleared using the "Unit Check Mode" screen, press the "Back" switch to return to the "System Check Mode" screen and perform this operation.





FINISH DIAGNOSTIC MODE


a.

There are 2 methods to end diagnostic mode. Use one of them.

i.

Turn the ignition switch off.


ii.

Press and hold the "AUDIO" switch for 3 seconds.