w/ Rear Differential Lock:
The skid control ECU (brake actuator assembly) monitors the rear differential lock position switch (No. 4 transfer indicator switch) and if the rear differential is locked, at which time the rear differential lock indicator light is illuminated, the skid control ECU (brake actuator assembly) prohibits the ABS.
At the same time, the skid control ECU (brake actuator assembly) illuminates the ABS warning light.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1248/48 | Open Circuit in Rear Differential Lock | At a vehicle speed of 50 km/h (31 mph) or more, 3 seconds or more elapse after the rear differential changes from free to lock.
|
·
w/ Rear Differential Lock: ·
Rear differential lock position switch (No. 4 transfer indicator switch) ·
Differential lock system ·
EXI2 terminal circuit ·
Skid control ECU (Brake actuator assembly) |
Before disconnecting the connector, make sure that there are no problems with the connection.
After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.
| *a | Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly]) |
w/ Rear Differential Lock: Set the vehicle to the rear differential free state.
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A13-22 (EXI2) - Body ground | Ignition switch ON | 11 to 14 V |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Rear Differential Lock) | B |
| NG (w/o Rear Differential Lock) | C |
A
B
C
Clear the DTC.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
w/ Rear Differential Lock: Set the vehicle to the rear differential free state.
Drive the vehicle at a speed of 50 km/h (31 mph) or more for 3 seconds or more.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC output | A |
| DTC not output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the ignition switch off.
Remove the rear differential lock position switch (No. 4 transfer indicator switch).
Inspect the rear differential lock position switch (No. 4 transfer indicator switch).
Click hereDrivetrain>AXLE AND DIFFERENTIAL>DIFFERENTIAL SYSTEM(w/ Differential Lock)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL CARRIER ASSEMBLY(w/ Differential Lock)>REMOVAL
Turn the ignition switch off.
Disconnect the rear differential lock position switch (No. 4 transfer indicator switch) connector.
Disconnect the rear differential lock ECU (No. 2 4 wheel drive control ECU) connector.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the G20 combination meter connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A13-22 (EXI2) - L8-2 | Always | Below 1 Ω |
| A13-22 (EXI2) - G20-9 (L) | Always | Below 1 Ω |
| A13-22 (EXI2) - K44-1 (RLP) | Always | Below 1 Ω |
| A13-22 (EXI2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereDrivetrain>AXLE AND DIFFERENTIAL>DIFFERENTIAL SYSTEM(w/ Differential Lock)>PROBLEM SYMPTOMS TABLE
NG