Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV with i-ART) › from 2014.10
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052493 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV with i-ART) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV with i-ART)  P0751  Shift Solenoid "A" Performance (Shift Solenoid Valve S1)  


DESCRIPTION

The TCM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th or 5th gear).

Then the TCM compares the actual gear with the shift schedule in the TCM memory to detect mechanical problems with the shift solenoid valves, valve body or automatic transmission (clutch, brake, gear, etc.).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0751 Shift Solenoid "A" Performance (Shift Solenoid Valve S1) Gear required by the TCM does not match the actual gear when driving (2-trip detection logic).
·

Shift solenoid valve S1 remains open or closed

·

Shift solenoid valve SLT remains open or closed

·

Valve body is blocked

·

Automatic transmission (clutch, brake, gear, etc.)


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates a stuck ON malfunction or stuck OFF malfunction of shift solenoid valve S1.

The TCM commands gear shifts by turning the shift solenoid valves ON/OFF. When the gear position commanded by the TCM and the actual gear position are not the same, the TCM illuminates the MIL and stores the DTC.

CAUTION / NOTICE / HINT

ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / ECT / Active Test.


g.

According to the display on the GTS, perform the Active Test.

HINT:

While driving, the shift position can be forcibly changed with the GTS.

Comparing the shift position commanded by the Active Test with the actual shift position enables you to confirm the problem (See page Drivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV with i-ART)>FAIL-SAFE CHART).


Powertrain > ECT > Active Test
Active Test Display
Control the Shift Position
Data List Display
Shift Status
50004 64 116 181
Powertrain > ECT > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Control the Shift Position Operate shift solenoid valves and set each shift position
·

Press "→" button: Shift up

·

Press "←" button: Shift down


Possible to check operation of the shift solenoid valves.
[Vehicle Condition]
50 km/h (31 mph) or less
HINT:
·

This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.

·

The 4th to 5th up-shift must be performed with the accelerator pedal released.

·

The 5th to 4th down-shift must be performed with the accelerator pedal released.

·

Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.

·

The shift position commanded by the TCM is shown in the Data List display on the GTS.

·

Shift solenoid valve S1 is turned ON/OFF normally when the shift lever is in D.

TCM gear shift command 1st 2nd 3rd 4th 5th
Shift solenoid valve S1 ON ON OFF OFF OFF





PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0751)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / DTC.

Powertrain > ECT > Trouble Codes
50001 64

e.

Read the DTCs using the GTS.

Result:
Result Proceed to
Only P0751 is output A
P0751 and other DTCs are output B


HINT:

If any other codes besides P0751 are output, perform troubleshooting for those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (SHIFT SOLENOID VALVE SLT)

B

2.PERFORM ACTIVE TEST USING GTS (SHIFT SOLENOID VALVE SLT)
NOTICE:
·

Perform the test while the ATF temperature is between 50 and 80°C (122 and 176°F).

·

Be careful to prevent the hose of SST from interfering with the exhaust pipe.

·

Perform the test with the A/C off.



HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.
C214323N06
0.594,1.198 0.594,1.688 0.594,1.688 0.427,1.688 false 2.75,1.24 2.75,1.688 2.75,1.688 2.906,1.688 true 0.125,1.615 0.479,1.813 0.354,0.198 10 false SST 2.99,1.604 3.313,1.802 0.323,0.198 10 false SST

Remove the test plug from the transmission case and connect SST.


SST
09992-00095  (09992-00231, 09992-00271)

b.

Connect the GTS to the DLC3.


c.

Start the engine and warm it up.


d.

Measure the line pressure with SST.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / ECT / Active Test.


g.

According to the display on the GTS, perform the Active Test.


h.

Measure the line pressure.

Powertrain > ECT > Active Test
Tester Display
Activate the Solenoid (SLT)
50004 64 130
Powertrain > ECT > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Activate the Solenoid (SLT) Operate shift solenoid valve SLT and raise line pressure ON or OFF
HINT:
·

OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, TCM commands shift solenoid valve SLT to turn OFF)

·

ON: No action (normal operation)



[Vehicle Condition]
·

Vehicle stopped

·

Engine idling


HINT:

Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Drivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV with i-ART)>HYDRAULIC TEST) as well. Note that the pressure values in the Active Test and hydraulic test are different.


OK:

The line pressure changes as specified when performing the Active Test.



Result:
Proceed to
OK
NG



OK

3.INSPECT SHIFT SOLENOID VALVE S1

NG

3.INSPECT SHIFT SOLENOID VALVE S1
a.
C214327C06
0.052,0.042 0.281,0.188 0.229,0.146 10 false *a 2.479,0.281 2.813,0.531 0.333,0.25 10 false (+) 3.208,0.26 3.427,0.5 0.219,0.24 10 false (-)
*a Component without harness connected
(Shift Solenoid Valve S1)


Remove shift solenoid valve S1.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve S1 connector terminal - Shift solenoid valve S1 body 20°C (68°F) 11 to 15 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Shift solenoid valve S1 connector

·

Battery negative (-) → Shift solenoid valve S1 body


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY

OK:

There are no foreign objects on any valve.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY