DTC P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) |
DTC P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2) |
DTC P0138 Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0136 |
|
|
| P0137 |
|
|
| P0138 |
|
|


| Required Sensors/Components (Main) | Heated oxygen sensor |
| Required Sensors/Components (Related) | Crankshaft position sensor, engine coolant temperature sensor, mass air flow meter sub-assembly, throttle position sensor and air fuel ratio sensor |
| Frequency of Operation | Once per driving cycle: Active air-fuel ratio control detection Continuous: Other |
| Active air-fuel ratio control | Executing |
| Active air-fuel ratio control begins when all of following conditions met: | - |
| Battery voltage | 11 V or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Idling | OFF |
| Engine speed | Less than 4000 rpm |
| Air fuel ratio sensor status | Activated |
| Fuel system status | Closed loop |
| Engine load | 10 to 80% |
| Either of following conditions met: | 1 or 2 |
| 1. Both of following conditions met | (a) and (b) |
| (a) Commanded air-fuel ratio | 14.3 or less |
| (b) Rear heated oxygen sensor voltage | 0.21 to 0.59 V |
| 2. Both of following conditions met | (c) and (d) |
| (c) Commanded air-fuel ratio | 14.9 or more |
| (d) Rear heated oxygen sensor voltage | 0.21 to 0.59 V |
| Both of following conditions met | (a) and (b) |
| (a) Commanded air-fuel ratio | 14.3 or less |
| (b) Rear heated oxygen sensor voltage | Below 0.21 V |
| Both of following conditions met | (a) and (b) |
| (a) Commanded air-fuel ratio | 14.9 or more |
| (b) Rear heated oxygen sensor voltage | Higher than 0.59 V |

| Intelligent tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| Intelligent tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 (A/F) | +12.5% | Rich | Below 3.1 V |
| AFS Voltage B1S1 (A/F) | -12.5% | Lean | Higher than 3.4 V |
| O2S B1S2 (HO2) | +12.5% | Rich | Higher than 0.55 V |
| O2S B1S2 (HO2) | -12.5% | Lean | Below 0.4 V |
| Case | Air Fuel Ratio Sensor (Sensor 1) Output Voltage | Heated Oxygen Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() ![]() | ![]() ![]() | - |
| 2 | ![]() ![]() | ![]() ![]() |
|
| 3 | ![]() ![]() | ![]() ![]() |
|
| 4 | ![]() ![]() | ![]() ![]() |
|
| 1.READ OUTPUT DTC |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
| P0138 is output | A |
| P0137 is output | B |
| P0136 is output | C |
| P0136, P0137 or P0138 and other DTCs are output | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / O2S B1S2.
Allow the engine to idle.
Read the heated oxygen sensor output voltage while idling.
| Heated Oxygen Sensor Output Voltage | Proceed to |
| 1.0 V or higher | A |
| Below 1.0 V | B |
|
| ||||
| A | |
| 3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT) |
![]() |
Disconnect the heated oxygen sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (+B) - 3 (OX1B) | Always | 10 kΩ or higher |
| 2 (+B) - 4 (E2) | Always | 10 kΩ or higher |
| *a | Component without harness connected (to Heated Oxygen Sensor for Bank 1) |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT) |
Turn the ignition switch off and wait for 5 minutes.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E11-2 (HT1B) - E11-25 (OX1B) | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME) |
Connect the intelligent tester to the DLC3.
Turn the intelligent tester on.
Start the engine.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
Change the fuel injection volume using the intelligent tester and monitor the voltage output of the air fuel ratio and heated oxygen sensors displayed on the intelligent tester.
| Intelligent tester Display (Sensor) | Voltage Variation | Proceed to |
| AFS Voltage B1S1 | Alternates between higher than and below 3.3 V | OK |
| Remains higher than 3.3 V | NG | |
| Remains below 3.3 V | NG |

|
| ||||
| OK | |
| 6.INSPECT AIR FUEL RATIO SENSOR |
Clear DTCs (Click here).
Drive the vehicle according to the driving pattern listed below.
Warm up the engine.
Drive the vehicle at 60 km/h (40 mph) or more for 10 minutes or more.
Stop the vehicle.
Accelerate the vehicle to 60 km/h (40 mph) or more and decelerate for 5 seconds or more. Perform this 3 times.

Enter the following menus: Powertrain / Engine and ECT / Data List / AFS Current B1S1.
Read the value of the air fuel ratio sensor current while the fuel-cut operation is being performed.
|
| ||||
|
| ||||
| 7.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the intelligent tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / O2S B1S2.
Change the fuel injection volume using the intelligent tester and monitor the voltage output of the heated oxygen sensors displayed on the intelligent tester.
|
| ||||
| OK | |
| 8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the intelligent tester on.
Start the engine.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
Change the fuel injection volume using the intelligent tester and monitor the voltage output of the air fuel ratio and heated oxygen sensors displayed on the intelligent tester.
| Intelligent tester Display (Sensor) | Voltage Variation | Proceed to |
| AFS Voltage B1S1 | Alternates between higher than and below 3.3 V | OK |
| Remains higher than 3.3 V | NG | |
| Remains below 3.3 V | NG |

|
| ||||
| OK | ||
| ||
| 9.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leakage.
|
| ||||
| OK | |
| 10.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
Inspect the heated oxygen sensor (Click here).
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
Disconnect the heated oxygen sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H5-1 (HT1B) - E11-2 (HT1B) | Always | Below 1 Ω |
| H5-3 (OX1B) - E11-25 (OX1B) | Always | Below 1 Ω |
| H5-4 (E2) - E11-28 (E2) | Always | Below 1 Ω |
| H5-1 (HT1B) or E11-2 (HT1B) - Body ground | Always | 10 kΩ or higher |
| H5-3 (OX1B) or E11-25 (OX1B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 12.REPLACE HEATED OXYGEN SENSOR |
Replace the heated oxygen sensor (Click here).
| NEXT | |
| 13.PERFORM CONFIRMATION DRIVING PATTERN |
Perform Confirmation Driving Pattern (P0136, P0137 and P0138).
| NEXT | |
| 14.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138 IS OUTPUT AGAIN) |
Connect the intelligent tester to the DLC3.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTCs: P0136, P0137 and P0138.
Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.
| Display (DTC Output) | Proceed to |
| ABNORMAL (P0136, P0137 or P0138 output) | A |
| NORMAL (No DTC output) | B |
|
| ||||
| A | ||
| ||
| 15.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 16.PERFORM CONFIRMATION DRIVING PATTERN |
Perform Confirmation Driving Pattern (P0136, P0137 and P0138).
| NEXT | |
| 17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138 IS OUTPUT AGAIN) |
Connect the intelligent tester to the DLC3.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTCs: P0136, P0137 or P0138.
Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.
| Display (DTC Output) | Proceed to |
| ABNORMAL (P0136, P0137 or P0138 output) | A |
| NORMAL (No DTC output) | B |
|
| ||||
| A | ||
| ||