DTC P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) |
DTC P0032 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1) |
DTC P101D A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0031 | The heater current is below the specified value while the heater is operating (1 trip detection logic). |
|
| P0032 | An air fuel ratio sensor heater current failure (1 trip detection logic). |
|
| P101D | The heater current is higher than the specified value while the heater is not operating (1 trip detection logic). | ECM |
| 1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the air fuel ratio sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (HA1A) - 2 (+B) | 20°C (68°F) | 1.6 to 3.2 Ω |
| 1 (HA1A) - 4 (A1A-) | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.CHECK TERMINAL VOLTAGE (POWER SOURCE) |
![]() |
Disconnect the air fuel ratio sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A5-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Air Fuel Ratio Sensor) |
Reconnect the air fuel ratio sensor connector.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A5-1 (HA1A) - E22-6 (HA1A) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A5-1 (HA1A) or E22-6 (HA1A) - Body ground | Always | 10 kΩ or higher |
Reconnect the air fuel ratio sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032 OR P101D) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Clear DTCs (Click here).
Start the engine and idle it for 5 minutes or more.
With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0031, P0032 or P101D is output | B |
|
| ||||
| A | ||
| ||
| 5.INSPECT AIR FUEL RATIO SENSOR HEATER RELAY (A/F) |
![]() |
Inspect the A/F relay.
Remove the A/F relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | Always | 10 kΩ or higher |
| 3 - 5 | Always | Below 1 Ω (when battery voltage is applied to terminals 1 and 2) |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (A/F SENSOR - A/F RELAY, A/F RELAY - INTEGRATION RELAY) |
Disconnect the air fuel ratio sensor connector.
Remove the A/F relay from the engine room relay block.
Remove the integration relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A5-2 (+B) - A/F relay terminal (3) | Always | Below 1 Ω |
| A/F relay terminal (5) - 1H-1 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A5-2 (+B) or A/F relay terminal (3) - Body ground | Always | 10 kΩ or higher |
| A/F relay terminal (5) or 1H-1 - Body ground | Always | 10 kΩ or higher |
Reconnect the air fuel ratio sensor connector.
Reinstall the integration relay.
Reinstall the A/F relay.
|
| ||||
| OK | ||
| ||