Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2A00    A/F Sensor Circuit Slow Response (Bank 1 Sensor 1)

DTC    P2A03    A/F Sensor Circuit Slow Response (Bank 2 Sensor 1)

for Preparation Click here


DESCRIPTION

Refer to DTC P2195 .

DTC No.
DTC Detection Condition
Trouble Area
P2A00
P2A03
Calculated test value for A/F sensor response rate deterioration level is less than threshold
  1. Air fuel ratio sensor
  2. ECM

CONFIRMATION DRIVING PATTERN

HINT:
Performing this confirmation driving pattern will activate the A/F sensor response monitor.


A231470E04

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the tester on.
  4. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON and turn the tester on.
  7. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].
  8. Drive the vehicle at approximately 60 km/h (38 mph) for 10 minutes or more in a city area [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  9. Enter the following menus: Powertrain / Engine and ECT / DTC [C].
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P2A00 or P2A03.
  13. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    UNKNOWN
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the test result is INCOMPLETE or UNKNOWN and no pending DTC is output, perform the following procedure.

  14. Drive the vehicle at a speed between 75 and 100 km/h (47 and 63 mph) for 10 minutes [D].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  15. Check the DTC judgment result [E].

WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

HINT:
Intelligent tester only:
Malfunctioning areas can found by performing the Active Test / Control the Injection volume operation. The "Control the injection volume" operation can determine if the A/F sensor, heated oxygen sensor or other potential trouble areas are malfunctioning or not.

Perform Active Test using the intelligent tester.

HINT:
"Control the injection volume" is an Active Test which changes the injection volume to -12.0% or +12.0%.

  1. Connect the intelligent tester to the DLC3.
  2. Start the engine and turn the tester ON.
  3. Warm up the engine by running the engine at 2500 rpm for approximately 90 seconds.
  4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the injection volume.
  5. Enter the following monitor items: AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2.
  6. Perform the "Control the injection volume" operation with the engine idling (press the right or left button).

HINT:
  1. The "Control the injection volume" operation lowers the fuel injection volume by 12.0% or increases the injection volume by 12.0%.
  1. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


Standard: 
Tester Display
(Sensor)
Injection Volume
Status
Voltage
AFS B1S1 or AFS B2S1
(A/F)
+12%
Rich
Less than 3.1 V
AFS B1S1 or AFS B2S1
(A/F)
-12%
Lean
More than 3.4 V
O2S B1S2 or O2S B2S2
(heated oxygen sensor)
+12%
Rich
More than 0.55 V
O2S B1S2 or O2S B2S2
(heated oxygen sensor)
-12%
Lean
Less than 0.4 V

NOTICE:
The A/F sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


Case
Air Fuel Ratio Sensor (Sensor 1) Output Voltage
Heated Oxygen Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E05
A151324E08
A150787E05
A150788E06
-
2
A150787E05
A150790E01
A150787E05
A150788E06
  1. Air fuel ratio sensor
  2. Air fuel ratio sensor heater
  3. Air fuel ratio sensor circuit
3
A150787E05
A151324E08
A150787E05
A150790E01
  1. Heated oxygen sensor
  2. Heated oxygen sensor heater
  3. Heated oxygen sensor circuit
4
A150787E05
A150790E01
A150787E05
A150790E01
  1. Fuel injector assembly
  2. Fuel pressure
  3. Gas leak from exhaust system (air-fuel ratio extremely rich or lean)
  1. Following the Control the injection volume procedure enables technicians to check and graph the voltage outputs of both the A/F and heated oxygen sensors.
  2. Enter the following menus on the tester: Powertrain / Engine and ECT / Active Test / Control the injection volume / Data List / AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2.

HINT:
  1. Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. These DTCs are related to the A/F sensor.
  3. These DTCs are recorded when the A/F sensor has malfunction, although the caption is oxygen sensor.

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00 AND/OR P2A03)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P2A00 and/or P2A03 is output
    A
    P2A00 and/or P2A03 and other DTCs are output
    B

    HINT:
    If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.



B
GO TO RELEVANT DTC CHART
A


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

  1. Perform the Control the Injection Volume operation with the engine idling.

  1. Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the tester.

    HINT:
    1. Change the fuel injection volume within the range of - 12.0% to +12.0%. The injection volume can be changed in fine gradations.
    2. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


    Tester Display (Sensor)
    Injection Volume
    Status
    Voltage
    AFS Voltage B1S1 or AFS Voltage B2S1
    (Air fuel ratio)
    +12%
    Rich
    Below 3.1 V
    AFS Voltage B1S1 or AFS Voltage B2S1
    (Air fuel ratio)
    -12%
    Lean
    Higher than 3.4 V
    O2S B1S2 or O2S B2S2
    (Heated oxygen)
    +12%
    Rich
    Higher than 0.55 V
    O2S B1S2 or O2S B2S2
    (Heated oxygen)
    -12%
    Lean
    Below 0.4 V

    Result:

    Status of AFS Voltage B1S1 or AFS Voltage B2S1
    Status of O2S B1S2 or O2S B2S2
    Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    A
    Lean
    Lean
    Actual air fuel ratio lean
    B
    Rich
    Rich
    Actual air fuel ratio rich
    B
    Lean
    Lean/Rich
    Air fuel ratio sensor malfunction
    C
    Rich
    Lean/Rich
    Air fuel ratio sensor malfunction
    C

    Lean: During the Control the Injection Volume Active Test, the air fuel ratio sensor output voltage (AFS Voltage) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently below 0.4 V.
    Rich: During the Control the Injection Volume Active Test, the AFS Voltage is consistently below 3.1 V, and the O2S is consistently higher than 0.55 V.
    Lean/Rich: During the Control the Injection Volume Active Test, the output voltage of the heated oxygen sensor alternates correctly.

  1. Refer to "Data List / Active Test" [AFS Voltage B1S1, AFS Voltage B2S1, O2S B1S2 and O2S B2S2] (Click here).



B
Go to step 4

C
Go to step 8
A


3.PERFORM CONFIRMATION DRIVING PATTERN
  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    NORMAL (DTC is not output)
    A
    ABNORMAL (DTC P2A00 or P2A03 is output)
    B



B
Go to step 8
A

CHECK FOR INTERMITTENT PROBLEMS 

4.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
A085152E37
  1. Disconnect the A35 and A36 A/F sensor connectors.

  1. Measure the resistance of the A/F sensor.

    Standard resistance:
    Bank 1 
    Tester Connection
    Condition
    Specified Condition
    1 (HA1A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA1A) - 4 (A1A-)
    -
    10 kΩ or higher
    Bank 2 
    Tester Connection
    Condition
    Specified Condition
    1 (HA2A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA2A) - 4 (A2A-)
    -
    10 kΩ or higher



NG
REPLACE AIR FUEL RATIO SENSOR
OK


5.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


6.CHECK FUEL PRESSURE
  1. Check the fuel pressure.



NG
Go to step 12
OK


7.INSPECT FUEL INJECTOR ASSEMBLY
  1. Inspect the fuel injector assembly.



NG
REPLACE FUEL INJECTOR ASSEMBLY
OK


8.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor.


NEXT


9.PERFORM CONFIRMATION DRIVING PATTERN
  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    ABNORMAL (DTC P2A00 or P2A03 is output)
    A
    NORMAL (DTC is not output)
    B



B
END
A


10.REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


11.PERFORM CONFIRMATION DRIVING PATTERN
  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Check that the DTC judgment result is NORMAL.


NEXT

END 

12.INSPECT FUEL PUMP
  1. Inspect the fuel pump .



NG
REPLACE FUEL PUMP
OK

REPAIR OR REPLACE FUEL LINE