Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2195    Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)

DTC    P2196    Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)

DTC    P2197    Oxygen (A/F) Sensor Signal Stuck Lean (Bank 2 Sensor 1)

DTC    P2198    Oxygen (A/F) Sensor Signal Stuck Rich (Bank 2 Sensor 1)

for Preparation Click here


DESCRIPTION

The Air-fuel Ratio (A/F) sensor generates voltage* in response to the actual air-fuel ratio. This sensor output voltage provides feedback to the ECM. The ECM uses the feedback to control the air-fuel ratio. Using the sensor output voltage, the ECM determines the deviation from the stoichiometric air-fuel ratio, and regulates the injection time. If the A/F sensor is malfunctioning, the ECM is unable to control the air-fuel ratio accurately.
The A/F sensor is equipped with a heater which heats the zirconia element. The heater is also controlled by the ECM. When the intake air volume is low (the temperature of the exhaust gas is low), a current flows to the heater to heat the sensor to facilitate the detection of accurate oxygen concentration.
The A/F sensor is a planar type. The sensor and heater portions are narrow. The heat of the heater is conducted to the zirconia element through the alumina, accelerating sensor activation.
To obtain a high purification rate of carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) in the exhaust gas, a Three-Way Catalytic Converter (TWC) is used. The TWC is most efficient when the air-fuel ratio is maintained near the stoichiometric air-fuel ratio.

HINT:
*: The voltage value changes inside the ECM only.


A225097E01


DTC No.
DTC Detection Condition
Trouble Area
P2195
P2197
Condition (a) continues for 10 seconds or more
(a) A/F sensor voltage more than 3.8 V
  1. Open or short in air fuel ratio sensor circuit
  2. Air fuel ratio sensor
  3. Air fuel ratio sensor heater
  4. A/F relay
  5. Air fuel ratio sensor heater and A/F relay circuits
  6. Air induction system
  7. Fuel pressure
  8. Fuel injector
  9. ECM
P2195
P2197
While fuel cut operation performed (during vehicle deceleration), A/F sensor current 3.6 mA or more for 3 seconds
  1. Air fuel ratio sensor
  2. ECM
P2196
P2198
Condition (a) continues for 10 seconds or more
(a) A/F sensor voltage less than 2.8 V
  1. Open or short in air fuel ratio sensor circuit
  2. Air fuel ratio sensor
  3. Air fuel ratio sensor heater
  4. A/F relay
  5. Air fuel ratio sensor heater and A/F relay circuits
  6. Air induction system
  7. Fuel pressure
  8. Fuel injector
  9. ECM
P2196
P2198
While fuel cut operation performed (during vehicle deceleration), A/F sensor current 1.4 mA for 3 seconds (2 trip detection logic)
  1. Air fuel ratio sensor
  2. ECM

HINT:
  1. DTCs P2195 and P2196 indicate malfunctions related to bank 1 A/F sensor circuit.
  2. DTCs P2197 and P2198 indicate malfunctions related to bank 2 A/F sensor circuit.
  3. Bank 1 refers to the bank that includes the No. 1 cylinder.
  4. Bank 2 refers to the bank that includes the No. 2 cylinder.
  5. Sensor 1 refers to the sensor closest to the engine assembly.
  6. After confirming DTC P2195, P2196 , P2197 and P2198 use the intelligent tester to confirm the voltage output of A/F sensor (AFS B1 S1 / AFS B2 S1) from the Powertrain / Engine and ECT / Data List.
  7. The A/F sensor's output voltage and the short-term fuel trim value can be read using the intelligent tester.
  8. The ECM controls the voltage of the A1A+, A2A+, A1A- and A2A- terminals of the ECM to the fixed voltage. Therefore, it is impossible to confirm the A/F sensor output voltage without the intelligent tester.


WIRING DIAGRAM


A243230E02


CONFIRMATION DRIVING PATTERN

This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.

A199318E33


A232909E02

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the tester on.
  4. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON and turn the tester on.
  7. Start the engine and warm it up until the ECT reaches 75°C (167°F) or higher [A].
  8. On the tester, enter the following menus to check the fuel-cut status: Powertrain / Engine and ECT / Data List / Idle Fuel Cut.
  9. Drive the vehicle at a speed between 60 and 100 km/h (38 and 63 mph) for at least 10 minutes [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  10. Shift the transmission to 2nd gear [C].
  11. Accelerate the vehicle to 60 km/h (38 mph) or more by depressing the accelerator pedal for at least 10 seconds [D].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  12. Soon after performing step [D] above, release the accelerator pedal for at least 4 seconds without depressing the brake pedal in order to execute fuel-cut control [E].

    HINT:
    Fuel-cut is performed when the following conditions are met:
    1. Accelerator pedal is fully released.
    2. Engine speed is 2500 rpm or more (fuel injection returns at 1000 rpm).

  13. Allow the vehicle to decelerate until the vehicle speed decreases to less than 10 km/h (6 mph).
  14. Repeat steps [C] through [E] above at least 3 times in one driving cycle.
  15. Enter the following menus: Powertrain / Engine and ECT / DTC [F].
  16. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  17. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  18. Input the DTC: P2195, P2196, P2197 or P2198.
  19. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    UNKNOWN
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or UNKNOWN, perform steps [B] through [F] again.


INSPECTION PROCEDURE

HINT:
Intelligent tester only:
Malfunctioning areas can found by performing the Active Test / Control the Injection volume operation. The "Control the injection volume for A/F sensor" operation can determine if the A/F sensor, heated oxygen sensor or other potential trouble areas are malfunctioning or not.

Perform the Active Test using the intelligent tester.

HINT:
"Control the injection volume" is an Active Test which changes the injection volume to -12.0% or +12.0%.

  1. Connect the intelligent tester to the DLC3.
  2. Start the engine and turn the tester ON.
  3. Warm up the engine by running the engine at 2500 rpm for approximately 90 seconds.
  4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the injection volume.
  5. Enter the following monitor items: AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2.
  6. Perform the "Control the injection volume for A/F sensor" operation with the engine idling (press the right or left button).

HINT:
  1. The "Control the injection volume" operation lowers the fuel injection volume by 12.0% or increases the injection volume by 12.0%.
  1. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


Standard: 
Tester Display
(Sensor)
Injection Volume
Status
Voltage
AFS B1S1 or AFS B2S1
(A/F)
+12%
Rich
Less than 3.1 V
AFS B1S1 or AFS B2S1
(A/F)
-12%
Lean
More than 3.4 V
O2S B1S2 or O2S B2S2
(heated oxygen sensor)
+12%
Rich
More than 0.55 V
O2S B1S2 or O2S B2S2
(heated oxygen sensor)
-12%
Lean
Less than 0.4 V

NOTICE:
The A/F sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


Case
Air Fuel Ratio Sensor (Sensor 1) Output Voltage
Heated Oxygen Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E05
A151324E08
A150787E05
A150788E06
-
2
A150787E05
A150790E01
A150787E05
A150788E06
  1. Air fuel ratio sensor
  2. Air fuel ratio sensor heater
  3. Air fuel ratio sensor circuit
3
A150787E05
A151324E08
A150787E05
A150790E01
  1. Heated oxygen sensor
  2. Heated oxygen sensor heater
  3. Heated oxygen sensor circuit
4
A150787E05
A150790E01
A150787E05
A150790E01
  1. Fuel injector assembly
  2. Fuel pressure
  3. Gas leak from exhaust system (air-fuel ratio extremely rich or lean)
  1. Following the Control the injection volume procedure enables technicians to check and graph the voltage outputs of both the A/F and heated oxygen sensors.
  2. Enter the following menus on the tester: Powertrain / Engine and ECT / Active Test / Control the injection volume / Data List / AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2.

HINT:
  1. Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. These DTCs are related to the A/F sensor.
  3. These DTCs are recorded when A/F sensor has malfunction, although the caption is oxygen sensor.

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195, P2196, P2197 OR P2198)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    P2195, P2196, P2197 or P2198 is output
    A
    "P2195, P2196, P2197 or P2198" and "P0136, P0137, P0138, P0156, P0157 or P0158" are output
    A
    P2195, P2196, P2197 or P2198 and other DTCs are output
    B

    HINT:
    If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.



B
GO TO DTC OUTPUT
A


2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
  1. Has the vehicle run out of fuel in the past?



NO
Go to step 4
YES


3.PERFORM CONFIRMATION DRIVING PATTERN
  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    NORMAL (DTC is not output)
    A
    ABNORMAL (DTC P2195, P2196, P2197 or P2198 is output)
    B



B
Go to step 4
A

DTC CAUSED BY RUNNING OUT OF FUEL 

4.READ VALUE USING INTELLIGENT TESTER (TEST VALUE OF AIR FUEL RATIO SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / AFS Current B1S1 and AFS Current B2S1.

  1. Check the test value of the air fuel ratio sensor output current during fuel-cut.

    Result:
    Test Value
    Proceed to
    Within normal range (1.4 mA or higher, and below 3.6 mA)
    A
    Outside normal range (below 1.4 mA, or 3.6 mA or higher)
    B



B
Go to step 14
A


5.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

  1. Perform the Control the Injection Volume operation with the engine idling.

  1. Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the tester.

    HINT:
    1. Change the fuel injection volume within the range of -12.0% to +12.0%. The injection volume can be changed in fine gradations.
    2. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


    Tester Display (Sensor)
    Injection Volume
    Status
    Voltage
    AFS Voltage B1S1 or AFS Voltage B2S1
    (Air fuel ratio)
    +12.0%
    Rich
    Below 3.1 V
    AFS Voltage B1S1 or AFS Voltage B2S1
    (Air fuel ratio)
    -12.0%
    Lean
    Higher than 3.4 V
    O2S B1S2 or O2S B2S2
    (Heated oxygen)
    +12.0%
    Rich
    Higher than 0.55 V
    O2S B1S2 or O2S B2S2
    (Heated oxygen)
    -12.0%
    Lean
    Below 0.4 V

    Result 
    Status of AFS Voltage B1S1 or AFS Voltage B2S1
    Status of O2S B1S2 or O2S B2S2
    Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition
    Misfire
    Suspected Trouble Area
    Proceed to
    Lean
    Lean
    Actual air fuel ratio lean
    May occur
    1. PCV valve and hose
    2. PCV hose connections
    3. Fuel injector blockage
    4. Gas leaks from exhaust system
    5. Intake system
    6. Fuel pressure
    7. Mass air flow meter assembly
    8. Engine coolant temperature sensor
    A
    Rich
    Rich
    Actual air fuel ratio rich
    -
    1. Fuel injector leakage or blockage
    2. Gas leaks from exhaust system
    3. Ignition system
    4. Fuel pressure
    5. Mass air flow meter assembly
    6. Engine coolant temperature sensor
    A
    Lean
    Lean/Rich
    Air fuel ratio sensor malfunction
    -
    Air fuel ratio sensor
    B
    Rich
    Lean/Rich
    Air fuel ratio sensor malfunction
    -
    Air fuel ratio sensor
    B
    Lean/Rich
    Lean/Rich
    Normal
    -
    -
    B
    Lean: During the Control the Injection Volume Active Test, the air fuel ratio sensor output voltage (AFS Voltage) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently below 0.4 V.
    Rich: During the Control the Injection Volume Active Test, the AFS Voltage is consistently below 3.1 V, and the O2S is consistently higher than 0.55 V.
    Lean/Rich: During the Control the Injection Volume Active Test, the output voltage of the heated oxygen sensor alternates correctly.

HINT:
Refer to "Data List / Active Test" [AFS Voltage B1S1, AFS Voltage B2S1, O2S B1S2 and O2S B2S2] (Click here).



B
Go to step 14
A


6.CHECK AIR INDUCTION SYSTEM
  1. Check the intake system for vacuum leaks.

    OK:
    No leaks in intake system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


7.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.



NG
REPAIR OR REPLACE EXHAUST SYSTEM
OK


8.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 16
OK


9.INSPECT FUEL INJECTOR ASSEMBLY
  1. Check the fuel injector assembly (whether fuel volume is high or low, and whether injector pattern is poor) (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY
OK


10.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


11.PERFORM CONFIRMATION DRIVING PATTERN
  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    ABNORMAL (DTC P2195, P2196, P2197 or P2198 is output)
    A
    NORMAL (DTC is not output)
    B



B
END
A


12.REPLACE ECM
  1. Replace the ECM.


NEXT


13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Check the DTC judgment result.

    Result 
    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    UNKNOWN
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit


NEXT

END 

14.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor.


NEXT


15.PERFORM CONFIRMATION DRIVING PATTERN
  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    NORMAL (DTC is not output)
    A
    ABNORMAL (DTC P2195, P2196, P2197 or P2198 is output)
    B



B
REPLACE ECM
A

END 

16.CHECK FUEL LINE
  1. Check the fuel lines for leaks or blockage.



NG
REPAIR OR REPLACE FUEL LINE
OK

REPLACE FUEL PUMP