DTC P0504 Brake Switch "A" / "B" Correlation |
| Signal (ECM Terminal) | Brake Pedal Released | In Transition | Brake Pedal Depressed |
| STP | OFF | ON | ON |
| ST1- | ON | ON | OFF |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0504 | Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic): (a) The ignition switch is ON. (b) The brake pedal is released. (c) The STP signal is off when the ST1- signal is off. |
|

| Brake Pedal Operation | Stop Light Switch | ST1 |
| Depressed | ON | ON |
| Released | OFF | OFF |
| 1.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE) |
![]() |
Disconnect the stop light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| S14-3 - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Stop Light Switch Assembly) |
Reconnect the stop light switch assembly connector.
|
| ||||
| OK | |
| 2.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE) |
![]() |
Disconnect the stop light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S14-2 - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector (to Stop Light Switch Assembly) |
Reconnect the stop light switch assembly connector.
|
| ||||
| OK | |
| 3.INSPECT STOP LIGHT SWITCH ASSEMBLY |
![]() |
Inspect the stop light switch assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - 2 | Pin not pushed | Below 1 Ω |
| 3 - 4 | Pin not pushed | 10 kΩ or higher |
| 1 - 2 | Pin pushed | 10 kΩ or higher |
| 3 - 4 | Pin pushed | Below 1 Ω |
|
| ||||
| OK | |
| 4.CHECK ECM (STP AND ST1- VOLTAGE) |
![]() |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Brake Pedal Operation | Specified Condition |
| E24-8 (ST1-) - Body ground | Brake pedal released | 7.5 to 14 V |
| Brake pedal depressed | Below 1.5 V | |
| E25-18 (STP) - Body ground | Brake pedal released | Below 1.5 V |
| Brake pedal depressed | 7.5 to 14 V |
| *a | Component with harness connected (ECM) |
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - IGNITION SWITCH ASSEMBLY) |
Disconnect the stop light switch assembly connector.
Disconnect the ignition switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S14-3 - I8-6 (IG2) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| S14-3 or I8-6 (IG2) - Body ground | Always | 10 kΩ or higher |
Reconnect the ignition switch connector.
Reconnect the stop light switch assembly connector.
|
| ||||
| OK | ||
| ||