Home › ENGINE ยท 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    P0504    Brake Switch "A" / "B" Correlation

for Preparation Click here


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate that the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:
The normal signal conditions are as shown in the table below.

Signal (ECM Terminal)
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF


P0504 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Depress and release brake pedal with ignition switch to ON
Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch to ON.
(b) Brake pedal is released.
(c) The STP signal is off when the ST1- signal is off, or the STP signal is on when the ST1- signal is on.
  1. Open or short in stop light switch signal circuit
  2. STOP fuse
  3. IGN fuse
  4. Stop light switch
  5. ECM

Related Data List 
DTC No.
Data List
P0504
Stop Light Switch

WIRING DIAGRAM


A154326E11


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

1.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL B VOLTAGE)


    A253393E07
  1. Disconnect the stop light switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S14-2 - Body ground
    Always
    11 to 14 V
    S14-3 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Switch)

  1. Reconnect the stop light switch connector.



NG
Go to step 6
OK


2.INSPECT STOP LIGHT SWITCH ASSEMBLY
  1. Inspect the stop light switch assembly (Click here).



NG
Go to step 4
OK


3.CHECK ECM (STP AND ST1- VOLTAGE)
A080995E22
  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Brake Pedal Condition
    Specified Condition
    E5-14 (ST1-) - Body ground
    Released
    11 to 14 V
    Depressed
    0 to 3 V
    E5-15 (STP) - Body ground
    Released
    0 to 3 V
    Depressed
    11 to 14 V

    Text in Illustration 
    *a
    Brake Pedal Depressed
    *b
    Brake Pedal Released
    *c
    Component with harness connected
    (ECM)

  1. Reconnect the ECM connector.



OK
Go to step 5

NG
Go to step 6

4.REPLACE STOP LIGHT SWITCH ASSEMBLY
  1. Replace the stop light switch assembly (Click here).



NEXT
Go to step 7

5.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 7

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Depress and release the brake pedal.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END