Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1413    Front Speed Sensor RH Output Malfunction

DTC    C1275    Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)

DTC    C1276    Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)

DTC    C1414    Front Speed Sensor LH Output Malfunction

for Preparation Click here


DESCRIPTION

Refer to DTCs C1401 and C1402 (Click here).

DTC Code
DTC Detection Condition
Trouble Area
C1413
C1414
One of the following conditions is met:
  1. An open in the sensor signal circuit occurs 255 times or more.
  2. At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals 75 times or more within 5 seconds.
  3. At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.
  1. Front speed sensor RH/LH
  2. Speed sensor circuit
  3. Front skid control rotor RH/LH
  4. Skid control ECU (Brake actuator assembly)
C1275
C1276
Stored during Test Mode.
  1. Front speed sensor RH/LH
  2. Front skid control rotor RH/LH

HINT:
  1. DTCs C1413 and C1275 are for the front speed sensor RH.
  2. DTCs C1414 and C1276 are for the front speed sensor LH.


WIRING DIAGRAM

Refer to DTCs C1405 and C1406 (Click here).

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the brake actuator assembly, perform calibration (Click here).
  2. Check the speed sensor signal after replacement (Click here).
  3. Before disconnecting the connector, make sure that there are no problems with the connection.
  4. After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Speed Open
    Front speed sensor RH open circuit detection / Error or Normal
    Normal
    -
    FL Speed Open
    Front speed sensor LH open circuit detection / Error or Normal
    Normal
    -

    OK:
    Normal (there are no momentary interruptions).

    HINT:
    Perform the above inspection before removing the sensor or disconnecting a connector.



NG
Go to step 8
OK


2.READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List, and then drive the vehicle.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Wheel Speed
    Front speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    No large fluctuations when driving at a constant speed.
    FL Wheel Speed
    Front speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    No large fluctuations when driving at a constant speed.

  1. Check the speed value output from the speed sensor displayed on the intelligent tester.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart (Click here).

    OK:
    The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
Go to step 5
OK


3.PERFORM TEST MODE (SIGNAL CHECK)
  1. Perform the signal check in the Test Mode procedure (Click here).

    OK:
    All Test Mode DTCs are cleared.



NG
Go to step 5
OK


4.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next suspected area (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)  

5.CHECK FRONT SPEED SENSOR INSTALLATION
  1. Turn the ignition switch off.



    C108871E12
  1. Check the speed sensor installation (Click here).
    Text in Illustration 
    *1
    Front Speed Sensor
    *a
    No clearance
    *b
    CORRECT
    *c
    INCORRECT

    OK:
    There is no clearance between the sensor and the steering knuckle.
    The installation bolt is tightened properly.



NG
INSTALL FRONT SPEED SENSOR CORRECTLY (Click here)
OK


6.INSPECT FRONT SPEED SENSOR TIP
  1. Turn the ignition switch off.

  1. Remove the front speed sensor (Click here).

  1. Check the speed sensor tip.

    OK:
    No scratches, oil or foreign matter on the sensor tip.

    NOTICE:
    Do not replace the speed sensor if no damage to the speed sensor tip is found.

    HINT:
    1. If the sensor is contaminated with oil or other foreign material, clean the sensor.
    2. If there is iron powder sticking to the rotor, this will result in a malfunction. Therefore, confirm that the rotor is not contaminated with foreign material before replacing the sensor.



NG
CLEAN OR REPLACE FRONT SPEED SENSOR
OK


7.INSPECT FRONT SKID CONTROL ROTOR
  1. Turn the ignition switch off.

  1. Remove the front skid control rotor (Click here).

  1. Check the front skid control rotor.

    OK:
    No scratches, oil or foreign matter on the rotor.



NG
CLEAN OR REPLACE FRONT SKID CONTROL ROTOR
OK


8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Disconnect the front speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    S25-7 (FR+) - S5-1 (FR+)
    Always
    Below 1 Ω
    S25-7 (FR+) - Body ground
    Always
    10 kΩ or higher
    S25-6 (FR-) - S5-2 (FR-)
    Always
    Below 1 Ω
    S25-6 (FR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    S25-19 (FL+) - S4-1 (FL+)
    Always
    Below 1 Ω
    S25-19 (FL+) - Body ground
    Always
    10 kΩ or higher
    S25-18 (FL-) - S4-2 (FL-)
    Always
    Below 1 Ω
    S25-18 (FL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK TERMINAL VOLTAGE (FR+, FL+ TERMINAL)
  1. Turn the ignition switch off.

  1. Connect the skid control ECU (brake actuator assembly) connector.

  1. Disconnect the front speed sensor connector.



    C237082E03
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for RH 
    Tester Connection
    Switch Condition
    Specified Condition
    S5-1 (FR+) - Body ground
    Ignition switch ON
    8 to 14 V
    for LH 
    Tester Connection
    Switch Condition
    Specified Condition
    S4-1 (FL+) - Body ground
    Ignition switch ON
    8 to 14 V

    Text in Illustration 
    *A
    for RH
    *B
    for LH
    *a
    Front view of wire harness connector
    (to Front Speed Sensor)



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


10.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
Go to step 11
A

USE SIMULATION METHOD TO CHECK (Click here)  

11.REPLACE FRONT SPEED SENSOR
  1. Turn the ignition switch off.

  1. Replace the front speed sensor (Click here).


NEXT


12.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPLACE FRONT SKID CONTROL ROTOR (Click here)
A

END