Home › ENGINE ยท 2TR-FBE › FUEL › FUEL SYSTEM

FUEL SYSTEM > ON-VEHICLE INSPECTION

for Preparation Click here



1. CHECK FOR FUEL PUMP OPERATION AND FUEL LEAKS
  1. Connect the intelligent tester to the DLC3.

    1. Turn the ignition switch to ON.

      NOTICE:
      Do not start the engine.

    2. Push the intelligent tester main switch on.

    3. Select the Active Test and enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check fuel pump operation.

    1. Check for pressure in the fuel inlet tube from the fuel line. Check that the sound of fuel flowing in the fuel tank can be heard.
      If there is no sound, check the integration relay, fuel pump, ECM and wiring connector.

  1. Check for fuel leaks.

    1. Check that there are no fuel leaks after performing maintenance anywhere on the system.
      If there are fuel leaks, repair or replace parts as necessary.



2. CHECK FUEL PRESSURE
  1. Check that the battery positive voltage is above 12 V.

  1. Discharge the fuel system pressure (Click here).

  1. Disconnect the cable from negative (-) battery terminal.

    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



    A263363
  1. Pinch and pull the No. 1 fuel hose (Click here).

    CAUTION:
    1. Always read the precautions (Click here) before disconnecting the fuel tube connector (quick type).
    2. The fuel tube may spray fuel as a result of retained pressure that remains in it. Do not allow fuel to be sprayed in the engine compartment.



    G039749E03
  1. Install SST (pressure gauge) as shown in the illustration.

    SST
    09268-31012   (90467-13001, 95336-08070, 09268-41500, 09268-41120)
    09268-45014   (09268-41200, 09268-41220)

  1. Wipe off any gasoline.

  1. Reconnect the negative (-) battery cable.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Operate the fuel pump.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

      NOTICE:
      Do not start the engine.

    3. Push the intelligent tester main switch on.

    4. Select the Active Test and enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Measure the fuel pressure.

    Standard fuel pressure:
    338 to 348 kPa (3.4 to 3.5 kgf/cm2, 49 to 50 psi)

    If the pressure is higher than the specification, replace the fuel pressure regulator.
    If the pressure is lower than the specification, check the fuel hoses and connections, fuel pump, fuel filter and fuel pressure regulator.

  1. Start the engine.

  1. Measure the fuel pressure.

    Standard fuel pressure:
    338 to 348 kPa (3.4 to 3.5 kgf/cm2, 49 to 50 psi)

    If the pressure is not as specified, check the fuel pump, pressure regulator and/or injectors.

  1. Stop the engine.

  1. Check that the fuel pressure remains as specified for 5 minutes after the engine has stopped.

    Standard fuel pressure:
    147 kPa (1.5 kgf/cm2, 21 psi) or higher

    If the pressure is not as specified, check the fuel pump, pressure regulator and/or injectors.

  1. After checking the fuel pressure, disconnect the negative (-) battery cable and carefully remove SST and the fuel tube connector to prevent gasoline from spraying.

  1. Reconnect the No. 1 fuel hose (fuel tube connector).

  1. Check for fuel leaks .