Home › INTRODUCTION › INTRODUCTION › REPAIR INSTRUCTION

REPAIR INSTRUCTION > INITIALIZATION



PROCEDURES NECESSARY WHEN CABLE IS DISCONNECTED/RECONNECTED TO BATTERY TERMINAL

Procedures Necessary when Cable is Disconnected/Reconnected to Battery Terminal 
Necessary Procedure
Effect or Inoperative Function when Necessary Procedure is not Performed
See page
Circling calibration
Compass
Click here
for Driver Side, w/ Jam Protection
Power window regulator motor initialization
  1. Jam protection function
  2. Power window control system (w/ Jam Protection Function)
Click here

NOTICE:
w/ Navigation System
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.


PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED

Procedures Necessary when ECU or Other Parts are Replaced 
Replacement Part
Necessary Procedure
Effect or Inoperative Function when Necessary Procedure is not Performed
See page
ECM (for 1GR-FE)
Register VIN
DTC P0630 is output
Click here
ECM (for 1KD-FTV, i-ART)
  1. Learning values save
  2. Learning values write
Engine starting
Click here
Engine assembly (for 1KD-FTV, i- ART)
Crank Time Compensation Rest
Engine starting
Click here
Crankshaft position sensor plate (for 1KD-FTV, i-ART)
Crank Time Compensation Rest
Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data
Fuel supply pump assembly (for 1KD-FTV, i-ART)
Supply pump initialization
Engine starting
Automatic transmission assembly, engine assembly or ECM (for 1KD-FTV, i-ART)
Automatic Transmission Initialization
Large shift shock
ECM (for 1KD-FTV, w/ EGR Cooler)
  1. Learning values save
  2. Learning values write
Engine starting
Click here
Engine assembly (for 1KD-FTV, w/ EGR Cooler)
  1. Injector compensation code registration
  2. Pilot quantity learning
Engine starting
Injector assembly (for 1KD-FTV, w/ EGR Cooler)
  1. Injector compensation code registration
  2. Pilot quantity learning
Engine starting
Fuel supply pump assembly (for 1KD-FTV, w/ EGR Cooler)
Supply pump initialization
Engine startability
Click here
ECM (for 1KD-FTV, w/o EGR Cooler)
  1. Learning values save
  2. Learning values write
Engine starting
Click here
Engine assembly (for 1KD-FTV, w/o EGR Cooler)
  1. Injector compensation code registration
  2. Pilot quantity learning
Engine starting
Injector assembly (for 1KD-FTV, w/o EGR Cooler)
  1. Injector compensation code registration
  2. Pilot quantity learning
Engine starting
Fuel supply pump assembly (for 1KD-FTV, w/o EGR Cooler)
Supply pump initialization
Engine startability
Click here
ECM (for 2TR-FBE)
Register VIN
DTC P0630 is output
Click here
for A750E, 1GR-FE
  1. Automatic transmission assembly
  2. ECM
  3. Engine assembly
Reset memory
Large shift shock
Click here
for A750F, 1GR-FE
  1. Automatic transmission assembly
  2. ECM
  3. Engine assembly
Reset memory
Large shift shock
Click here
for A750F, 1KD-FTV
  1. Automatic transmission assembly
  2. Valve body assembly
  3. Any of the shift solenoid valve
Reset memory
Large shift shock
Click here
Skid control ECU (Brake actuator assembly)
Yaw rate and acceleration sensor zero point calibration
VSC
Click here
  1. Yaw rate and acceleration sensor
  2. Front wheel alignment adjustment
  1. Clearing zero point calibration data
  2. Yaw rate and acceleration sensor zero point calibration
VSC
  1. Theft warning ECU assembly
  2. Key
Recognition code registration
Wireless door lock control system
Click here
  1. Transponder key ECU assembly
  2. ECM
  3. Key
Code registration
Engine starting
Refer to the Service Bulletin for the registration procedure.
w/ Blocking System
  1. Telephone transceiver assembly
  2. Instrument panel integration antenna assembly
  3. Divider antenna assembly
  4. Mayday battery
  1. Set contract mode
  2. Registration
Blocking system
Refer to the Service Bulletin for the registration procedure.
  1. Height control sensor
  2. Headlight leveling ECU
Headlight leveling ECU initialization
Headlight leveling function
Click here
Timing belt (for 1KD-FTV)
Timing belt information mode reset operation
  1. Does not illuminate when replacement is necessary
  2. Illuminates when replacement is not necessary
Click here
for Driver Side, w/ Jam Protection
  1. Front power window regulator motor
  2. Front door window regulator
  3. Power window regulator master switch
Motor initialization
  1. Jam protection function
  2. Power window control system (w/ Jam Protection Function)
Click here