Home › BODY ELECTRICAL › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM

WIRELESS DOOR LOCK CONTROL SYSTEM > Only Wireless Control Function is Inoperative

for Preparation Click here


DESCRIPTION

The theft warning ECU assembly receives a signal from the transmitter assembly and sends these signals to the instrument panel junction block. The instrument panel junction block then controls all the doors sending lock/unlock signals to each door lock assembly.

WIRING DIAGRAM


B258045E04


INSPECTION PROCEDURE

NOTICE:
When replacing the theft warning ECU assembly or door control transmitter sub-assembly, refer to the registration procedures (Click here).

1.CHECK POWER DOOR LOCK OPERATION
  1. Check the power door lock operation (Click here).

OK:
Each door locks and unlocks normally.



NG
Go to POWER DOOR LOCK CONTROL SYSTEM
OK


2.CHECK DOOR CONTROL TRANSMITTER ASSEMBLY
  1. Check whether the wireless door lock control functions operate normally with another registered door control transmitter assembly.

    OK:
    Wireless door lock control functions operate normally.



NG
Go to step 5
OK


3.CHECK DOOR CONTROL TRANSMITTER ASSEMBLY (LED)
  1. Press and hold the lock switch of the door control transmitter assembly for 5 seconds and check the number of times that the transmitter LED illuminates.
    Result 
    Result
    Proceed to
    Transmitter LED does not illuminate when switch is pressed and held
    A
    Transmitter LED illuminates 3 times or more when switch is pressed and held
    B
    Transmitter LED illuminates once or twice but not third time
    C



B
REPLACE DOOR CONTROL TRANSMITTER SUB-ASSEMBLY (Click here)

C
REPLACE TRANSMITTER BATTERY (Click here)
A


4.INSPECT TRANSMITTER BATTERY (VOLTAGE)


    B262355
  1. Remove the transmitter battery from the door control transmitter assembly that does not operate (Click here).

  1. Attach a lead wire (0.6mm [0.0236 in.] in diameter or less including wire sheath) with tape or equivalent to the negative battery.

    NOTICE:
    Do not wrap the lead wire around a terminal, wedge it between the terminals or solder it. A terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.

  1. Carefully extend the lead wire out from the position shown in the illustration and install the preciously removed transmitter battery.

NOTICE:
When replacing the transmitter battery, before staring work, remove any static electricity that has built up by touching, for example, the vehicle to prevent the door control transmitter sub-assembly from being damaged.

  1. Measure the voltage according to the value(s) in the table below.

    HINT:
    1. Measure the transmitter battery voltage while pressing the lock or unlock switch on the transmitter.
    2. Perform the measurement when the door control transmitter assembly is at room temperature.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Battery positive (+) - Battery negative (-)
    Ignition switch off, all doors closed and lock or unlock switch pushed
    2.2 to 3.2 V



NG
REPLACE TRANSMITTER BATTERY (Click here)
OK

REPLACE DOOR CONTROL TRANSMITTER SUB-ASSEMBLY (Click here)  

5.CHECK FOR ELECTRICAL NOISE
  1. Move the door control transmitter assembly in the vicinity of the theft warning ECU assembly.

    HINT:
    Refer to Parts Location for the location of the theft warning ECU assembly (Click here).

  1. Press and hold either the lock or unlock transmitter switch for 1 second and check that the doors lock or unlock accordingly.

    OK :
    Wireless door lock control functions operate normally.

    HINT:
    1. Check if electrical noise is the cause by moving the door control transmitter assembly closer to the theft warning ECU assembly. Moving it closer will decrease the effects of electrical noise.
    2. If the operation check can be performed normally, there is a high probability the electrical noise or decrease in output from the door control transmitter assembly is the cause of the malfunction. There is a high probability that electrical noise is the cause if the problem occurs only in a certain location or only during a certain time of day. Also, custom components may be causing electrical noise. If custom components are installed in the vehicle, remove them and perform the operation check again.



NG
Go to step 6
OK

FIND CAUSE OF NOISE AND REMOVE IT 

6.INSPECT UNLOCK WARNING SWITCH ASSEMBLY


    B274206E01
  1. Remove the unlock warning switch assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Not pushed
    10 kΩ or higher
    Pushed
    Below 1 Ω

    Text in Illustration 
    *1
    Pushed
    *b
    Not pushed



NG
REPLACE UNLOCK WARNING SWITCH ASSEMBLY
OK


7.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - THEFT WARNING ECU AND BODY GROUND)
  1. Disconnect the U1 unlock warning switch assembly connector.

  1. Disconnect the T33 theft warning ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    U1-1 - T33-5 (KSW)
    Always
    Below 1 Ω
    U1-1 or T33-5 (KSW) - Body ground
    Always
    10 kΩ or higher
    U1-2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (THEFT WARNING ECU - INSTRUMENT PANEL JUNCTION BLOCK)
  1. Disconnect the T33 theft warning ECU assembly connector.

  1. Disconnect the 2A and 2D instrument panel side junction block assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G29-25 (L2) - 2A-4 (L1)
    Always
    Below 1 Ω
    G29-26 (UL3) - 2D-4 (UL1)
    Always
    Below 1 Ω
    G29-25 (L2) or 2A-4 (L1) - Body ground
    Always
    10 kΩ or higher
    G29-26 (UL3) or 2D-4 (UL1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK HARNESS AND CONNECTOR (THEFT WARNING ECU - BATTERY AND BODY GROUND)


    B274165E11
  1. Disconnect the T33 theft warning ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G29-1 (E) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G29-4 (+B1) - Body ground
    Always
    11 to 14 V
    G29-14 (+B2) - Body ground
    Always
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Theft Warning ECU Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.REPLACE INSTRUMENT PANEL JUNCTION BLOCK
  1. Temporarily replace the driver side junction block assembly with a new or normally functioning one.

  1. Check that the wireless door lock control functions (Click here).

    OK:
    Wireless door lock control functions operate normally.



NG
REPLACE THEFT WARNING ECU ASSEMBLY
OK

END (INSTRUMENT PANEL JUNCTION BLOCK IS DEFECTIVE)