Home › DRIVE LINE › DIFFERENTIAL › DIFFERENTIAL CARRIER ASSEMBLY (for DANA Made)

DIFFERENTIAL CARRIER ASSEMBLY (for DANA Made) > DISASSEMBLY

for Preparation Click here



1. FIX REAR DIFFERENTIAL CARRIER ASSEMBLY


C121133


2. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR


F001237E03
  1. Using a dial indicator, measure the runout of the companion flange vertically and laterally.

    Maximum runout:
    Runout
    Maximum
    Vertical runout
    0.10 mm (0.0039 in.)
    Lateral runout
    0.10 mm (0.0039 in.)

    1. If the runout is greater than the maximum, replace the companion flange.



3. INSPECT RUNOUT OF DIFFERENTIAL RING GEAR


C121134
  1. Using a dial indicator, measure the runout of the ring gear.

    Maximum runout:
    0.07 mm (0.0028 in.)

    1. If the runout is greater than the maximum, replace the ring gear with a new one.



4. INSPECT DIFFERENTIAL RING GEAR BACKLASH


C121135
  1. Using a dial indicator, measure the backlash of the ring gear.

    Standard backlash:
    0.13 to 0.18 mm (0.0051 to 0.0071 in.)

    1. If the backlash is not within the specification, adjust the side bearing preload or repair as necessary.

      HINT:
      Perform the measurements at 3 or more positions around the side bearing preload.



5. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


C003092E01
  1. Using a torque wrench, measure the preload of backlash between the drive pinion and ring gear.

    Standard drive pinion preload (at start of torque):
    0.56 to 0.85 N*m (6 to 9 kgf*cm, 4.9 to 7.5 in.*lbf)

    1. If necessary, disassemble and inspect the differential.



6. INSPECT TOTAL PRELOAD


C003092E01
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

  1. Using a torque wrench, measure the total preload.

    HINT:
    A bolt without a torque specification is shown in the service data (Click here).

    1. If necessary, disassemble and inspect the differential.



7. REMOVE REAR DRIVE PINION NUT


F044346E01
  1. Using SST and a hammer, loosen the staked part of the nut.

    SST
    09930-00010   (09931-00010, 09931-00020)



    SA02349E03
  1. Using SST to hold the companion flange in place, remove the nut.

    SST
    09330-00021   (09330-00030)



8. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


B087869E01
  1. Using SST, remove the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



9. REMOVE REAR DIFFERENTIAL DUST DEFLECTOR


F040564E02
  1. Using SST and a press, press out the dust deflector.

    SST
    09950-60010   (09951-00380)
    09950-70010   (09951-07150)
    09950-00020  

    NOTICE:
    Do not drop the companion flange.



10. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL


SA02348E02
  1. Using SST, remove the oil seal from the differential carrier.

    SST
    09308-10010  



11. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


12. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


Z000641E01
  1. Using SST, remove the roller bearing (inner) from the drive pinion.

    SST
    09556-22010  



13. REMOVE DIFFERENTIAL CASE ASSEMBLY


C121136E01
  1. Place matchmarks on the bearing cap and differential carrier.

  1. Remove the 4 bolts and 2 differential bearing caps.

  1. Remove the 2 side shims.



    C028220E01
  1. Remove the rear differential case assembly from the differential carrier.

    HINT:
    Tag the 2 case bearing outer races to show the location for reassembly.



14. REMOVE DIFFERENTIAL DRIVE PINION
  1. Remove the drive pinion and bearing spacer from the differential carrier.



15. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING


R010668E01
  1. Using SST and a press, press out the roller bearing (inner) from the drive pinion.

    SST
    09950-00020  

    NOTICE:
    Do not drop the drive pinion.

    HINT:
    If the drive pinion or ring gear is damaged, replace them as a set.



16. REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER


17. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


F044358E01
  1. Using SST, remove the roller bearing (outer) from the carrier.

    SST
    09308-00010  

  1. Using a brass bar and hammer, tap out the oil storage ring from the carrier.

    HINT:
    If the bearing is damaged during removal, replace it.



18. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING


C091047E01
  1. Using a brass bar and hammer, tap out the rear tapered roller bearing (outer) from the carrier.

    HINT:
    If the bearing is damaged during removal, replace it.



19. REMOVE DIFFERENTIAL RING GEAR


C121137E01
  1. Place matchmarks on the ring gear and differential case.

  1. Remove the 10 ring gear set bolts.



    C014054E02
  1. Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.



20. INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT


C121138
  1. Install the rear differential case bearing to the differential case.

  1. Install the differential case to the differential carrier.

  1. Install the 2 bearing caps to the differential carrier with the 4 bolts.

    Torque:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }

  1. Using a dial indicator, measure the differential case runout.

    Maximum runout:
    0.07 mm (0.0028 in.)

  1. Remove the differential case.

  1. Remove the rear differential case bearing.



21. REMOVE REAR DIFFERENTIAL CASE BEARING


F040345E02
  1. Using SST, remove the 2 bearings from the differential case.

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00360)

    HINT:
    Do not remove the case bearing when not replacing the differential case.



22. INSPECT DIFFERENTIAL PINION AND SIDE GEAR
  1. Check that the differential pinion and differential side gear are not worn.

    1. If the differential pinion or differential side gear is not worn, replace the differential.



23. INSPECT DIFFERENTIAL CASE


F014547E02
  1. Measure the side gear backlash.

    1. Using a dial indicator, measure the side gear backlash while holding one pinion gear toward the differential case.

      Standard backlash:
      0.05 to 0.20 mm (0.0020 to 0.008 in.)

      1. If the backlash is not within the specified range, replace the differential case with a new one.