Home › TRANSMISSION ยท A343E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Inspect the torque converter clutch (Click here).



2. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY


C191485E01
  1. Install the torque converter clutch to the automatic transmission.

  1. Using a vernier caliper and straightedge, measure dimension A between the contact surfaces of the transmission and engine (*1), and the contact surfaces of the converter and drive plate *2. (#)



    C191486E01
  1. Using a vernier caliper and straightedge, measure dimension B shown in the illustration. Check that B is greater than A measured in step (#).

    Standard dimension:
    B = A + 1.00 mm (0.0394 in.) or more



3. INSTALL NO. 1 ENGINE MOUNTING INSULATOR REAR


G034579E01
  1. Install the engine mounting insulator to the transmission with the 4 bolts.

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }



4. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY


C193822E01
  1. Apply clutch spline grease to the surface of the torque converter centerpiece that contacts the crankshaft.

    Clutch spline grease:
    Toyota Genuine Clutch Spline Grease or equivalent
    Maximum grease amount:
    Approximately 1 g (0.353 oz)



    C196683E01
  1. Install the transmission to the engine with the 7 bolts.

    Torque:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf } for 17 mm head
    37 N*m{ 377 kgf*cm , 27 ft.*lbf } for 14 mm head

    NOTICE:
    Confirm 2 knock pins are on the transmission fitted surface of the engine clock before the transmission installation.



    C118034E01
  1. Install the exhaust manifold stay with the 3 bolts.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf } for bolt A
    30 N*m{ 306 kgf*cm , 22 ft.*lbf } for bolt B
    71 N*m{ 724 kgf*cm , 52 ft.*lbf } for bolt C



    G034529E01
  1. Hold the crankshaft pulley bolt with a wrench and install the 6 torque converter clutch mounting bolts.

    Torque:
    41 N*m{ 418 kgf*cm , 30 ft.*lbf }

    NOTICE:
    Install the black bolt first, and then install the silver bolts.



5. INSTALL FLYWHEEL HOUSING DUST SEAL


6. CONNECT WIRE HARNESS


7. CONNECT CONNECTOR
  1. Connect the connectors.

    1. Connect the temperature sensor connector.

    2. Connect the park/neutral position switch connector.

    3. Connect the 3 speed sensor connectors.

    4. Connect the transmission wire connector.



8. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


G034517E01
  1. *1: Install the 4 set bolts of the engine mounting insulator.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }

  1. *2: Install the frame crossmember with the 4 bolts and 4 nuts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



9. INSTALL STARTER ASSEMBLY

HINT:
Refer to "2TR-FE STARTING-STARTER-INSTALLATION" and install the starter.



10. INSTALL TRANSMISSION CONTROL CABLE BRACKET


G034516E01
  1. Install the control cable bracket with the 2 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



11. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


G034515E01
  1. Connect the control cable with the clip.

  1. Connect the control cable with the nut.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



12. CONNECT OIL COOLER TUBE


C118032E01
  1. Loosely install the tip of the oil cooler tube inlet to the automatic transmission by hand.

  1. Loosely install the tip of the oil cooler tube outlet to the automatic transmission by hand.

  1. Install the 3 clamps with the 3 bolts.

    Torque:
    5.0 N*m{ 50 kgf*cm , 44 in.*lbf } for A
    12 N*m{ 122 kgf*cm , 9 ft.*lbf } for B



    C118036E02
  1. Using union nut wrench, tighten the inlet and outlet tubes.

    Torque:
    34 N*m{ 346 kgf*cm , 25 ft.*lbf } for use without union nut wrench
    31 N*m{ 316 kgf*cm , 23 ft.*lbf } for use with union nut wrench

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).



13. INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY


C118024
  1. Coat a new O-ring with ATF, and install it to the oil filler tube.

  1. Install the oil filler tube with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Install the oil dipstick.



14. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

HINT:
Refer to "PROPELLER SHAFT-REAR PROPELLER SHAFT ASSEMBLY-INSTALLATION" and install the propeller with center bearing shaft.



15. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. Install the front exhaust pipe (Click here).



16. ADJUST SHIFT LEVER POSITION
  1. Move the shift lever to N.



    G034515E02
  1. Remove the nut and disconnect the control cable.



    D028682E01
  1. Turn the control shaft lever clockwise until it stops, and then turn it counterclockwise 2 notches to set it to the N position.

  1. While holding the control shaft lever slightly toward the R position side, connect the cable with the nut.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



17. ADD AUTOMATIC TRANSMISSION FLUID

Fluid type:
Toyota Genuine ATF Type T-IV



18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.



19. PERFORM INITIALIZATION
  1. Perform initialization (Click here).



20. INSPECT SHIFT LEVER POSITION
  1. When moving the shift lever from P to R with the ignition switch to ON and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.

  1. Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D, and moves in reverse after shifting to R.
    If the results are not as specified, inspect the park/ neutral position switch and check the shift lever.



21. CHECK FOR EXHAUST GAS LEAKS


22. INSPECT AUTOMATIC TRANSMISSION FLUID
  1. Inspect the automatic transmission fluid (Click here).