Home › TRANSMISSION ยท A340E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here)



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE NO .1 ENGINE UNDER COVER


4. REMOVE NO. 2 ENGINE UNDER COVER


5. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the 2 bolts and 2 compression springs.

  1. Disconnect the front exhaust pipe from the outlet pipe and remove the gasket.

  1. Remove the front exhaust pipe from the pipe support.



6. REMOVE PROPELLER SHAFT ASSEMBLY
(Click here)


7. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf }



8. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY


G039346E01
  1. Remove the transmission oil level dipstick.

  1. Remove the 2 bolts and oil filler tube.

  1. Remove the O-ring from the oil filler tube.



9. DISCONNECT OIL COOLER TUBE


G034850E02
  1. Using a union nut wrench, disconnect the inlet tube and outlet tube.



    G034255E01
  1. Remove the 3 bolts and 3 clamps.



10. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


G034515E01
  1. Remove the nut and disconnect the control cable.

  1. Remove the clip and disconnect the control cable.



11. REMOVE STARTER ASSEMBLY
(Click here)


12. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY


G034520E01
  1. Support the transmission with a transmission jack.



13. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


G034517E03
  1. Remove the 4 set bolts of the rear No. 1 engine mounting insulator.

  1. Remove the 4 nuts, 4 bolts and frame crossmember.



14. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR


    C238609E01
  1. Remove the 4 bolts, ground cable and engine mounting insulator.
    Text in Illustration 
    *1
    Ground Cable



15. DISCONNECT ENGINE WIRE


G034521E01
  1. Tilt the transmission downward.

    NOTICE:
    Make sure the cooling fan does not contact the fan shroud.



  1. Disconnect the 6 connectors and detach the 3 clamps.


    C236145E01


    Text in Illustration 
    *A
    LH Side
    *B
    RH Side



16. REMOVE WIRE HARNESS CLAMP BRACKET
  1. Remove the bolt and wire harness clamp bracket from the transmission.



17. REMOVE STIFFENER PLATE


  1. Remove the 4 bolts and stiffener plate RH (with clamp).


    C237879E01


    Text in Illustration 
    *A
    LH Side
    *B
    RH Side

  1. Remove the 4 bolts and stiffener plate LH.

  1. Remove the No. 4 cylinder block insulator.

  1. Remove the No. 2 end plate.



18. REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT
  1. Turn the crankshaft to gain access to each bolt.



    G034258E01
  1. Hold the crankshaft pulley bolt with a wrench, and remove the 6 drive plate and torque converter setting bolts.



19. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY


    G034259E03
  1. Remove the 5 bolts.
    Text in Illustration 
    *1
    Knock Pin

  1. Separate the transmission from the engine.

    NOTICE:
    To prevent damage to the knock pins, do not pry between the automatic transmission assembly and engine assembly.



20. REMOVE TRANSMISSION CONTROL CABLE BRACKET


G034516E01
  1. Remove the 2 bolts and control cable bracket from the transmission.



21. REMOVE TORQUE CONVERTER ASSEMBLY