Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)

AUDIO AND VISUAL SYSTEM (for Radio and Display Type) > Illumination Circuit

for Preparation Click here


DESCRIPTION

Power is supplied to the radio and display receiver assembly and steering pad switch assembly illumination when the headlight dimmer switch assembly is in the tail or head position.

WIRING DIAGRAM


E278682E04


INSPECTION PROCEDURE

CAUTION:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the SRS (Click here).

1.CHECK ILLUMINATION
  1. Check if the illumination for the radio and display receiver assembly, steering pad switch assembly, glove box or other parts (hazard switch, transmission control switch, etc.) comes on when the headlight dimmer switch is turned to the head or tail position.
    Result 
    Result
    Proceed to
    Illumination comes on for all components except steering pad switch assembly.
    A
    Illumination comes on for all components except radio and display receiver assembly.
    B
    No illumination comes on (radio and display receiver assembly, hazard switch, glove box, etc.).
    C



B
Go to step 6

C
GO TO LIGHTING SYSTEM (Click here)
A


2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BATTERY)


    E198671E32
  1. Disconnect the spiral cable sub-assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S28-12 (IL+2) - Body ground
    Headlight dimmer switch assembly tail or head position
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Spiral Cable Sub-assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Remove the steering pad switch assembly (Click here).

  1. Inspect the steering pad switch assembly (Click here).



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
  1. Remove the spiral cable sub-assembly (Click here).

  1. Inspect the spiral cable sub-assembly (Click here).



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)
  1. Disconnect the R21 radio and display receiver assembly connector.

  1. Disconnect the S28 spiral cable sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R21-23 (SWG) - S28-4 (EAU)
    Always
    Below 1 Ω
    R21-23 (SWG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)


    E277492E72
  1. Disconnect the radio and display receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R20-7 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    R20-10 (ILL+) - Body ground
    Headlight dimmer switch assembly tail or head position
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)