Home › TRANSMISSION ยท CLUTCH › CLUTCH UNIT

CLUTCH UNIT > INSTALLATION

for Preparation Click here



1. INSTALL INPUT SHAFT FRONT BEARING (for 1KD-FTV, 1GR-FE, 2KD-FTV)


Q007151E03
  1. Using SST and a hammer, tap in a new bearing.

    SST
    09304-12012  

    HINT:
    After installing the bearing to the hub, make sure that it rotates smoothly.

  1. Install 2 bolts.
    for 1GR-FE:
    for 1KD-FTV:
    for 2KD-FTV:



2. INSTALL INPUT SHAFT FRONT BEARING (for 2TR-FE)


Q007151E03
  1. Using SST and a hammer, tap in a new bearing.

    SST
    09304-12012  

    HINT:
    After installing the bearing to the hub, make sure that it rotates smoothly.

  1. Install 2 bolts.
    for 2TR-FE:
    for 2TR-FBE:



3. INSTALL CLUTCH DISC ASSEMBLY


    C226320
  1. Insert SST into the clutch disc. Then insert SST (together with the clutch disc) into the flywheel.

    SST
    09301-00110  

    NOTICE:
    Make sure not to insert the clutch disc facing the wrong direction.



4. INSTALL CLUTCH COVER ASSEMBLY


    D029623E03
  1. Align the matchmarks on the clutch cover and flywheel.

  1. Tighten the 6 bolts as described below.

    1. Determine the first bolt to be tightened by choosing the bolt closest to the knock pin.

    2. Uniformly tighten the 6 bolts in diametrically opposite pairs relative to the position of the first bolt. Use the illustration as a reference.

      Torque:
      19 N*m{ 195 kgf*cm , 14 ft.*lbf }

  1. Lightly move SST up and down, and right and left.

    SST
    09301-00110  

  1. Check that the disc is in the center, and then tighten the bolts.



5. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY


    D029624E01
  1. Using a dial indicator with roller instrument, measure the diaphragm spring tip alignment.

    Maximum misalignment:
    0.5 mm (0.020 in.)


    1. D029625E03
      If the misalignment is greater than the maximum, use SST to adjust the diaphragm spring tip alignment.
    SST
    09333-00013  



6. INSTALL RELEASE FORK SUPPORT
  1. Install the release fork support to the manual transmission unit.

    Torque:
    for 1KD-FTV, 2KD-FTV:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }
    for 1GR-FE:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }
    for 2TR-FE, 2TR-FBE:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }



7. INSTALL RELEASE BEARING HUB CLIP
  1. Install the release bearing hub clip to the release bearing.



8. INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY


C112689E06
  1. Apply Multemp 8158 grease or equivalent to the following areas:

    1. The contact surfaces of the release fork and release bearing hub.
    2. The contact surfaces of the release fork and push rod.
    3. The pivot points of the release fork.

      Grease:
      Multemp 8158 Grease or equivalent

  1. Install the release fork to the release bearing.



9. INSTALL CLUTCH RELEASE BEARING ASSEMBLY


    D029659E01
  1. Apply clutch spline grease to the input shaft spline.

    Grease:
    Toyota Genuine Clutch Spline Grease or equivalent

  1. Install the release fork (with release bearing) to the manual transmission.

    NOTICE:
    After the installation, move the fork forward and backward to check that the release bearing slides smoothly.



10. INSTALL CLUTCH RELEASE FORK BOOT


11. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY
  1. Install the manual transmission unit.
    R150/R151 manual transmission: (Click here).
    R150F/R151F manual transmission: (Click here).