Home › TRANSMISSION ยท R150F / R151F MANUAL TRANSMISSION › MANUAL TRANSMISSION ASSEMBLY

MANUAL TRANSMISSION ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL TRANSFER ASSEMBLY
  1. Install the transfer (Click here).



2. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY


C113299E08
  1. Align the input shaft with the clutch disc and install the transmission to the engine.

  1. 1KD-FTV:
    Install the 5 bolts.

    Torque:
    72 N*m{ 730 kgf*cm , 53 ft.*lbf }

  1. 2TR-FE:
    Install the 7 bolts.

    Torque:
    for bolt A:
    72 N*m{ 730 kgf*cm , 53 ft.*lbf }
    for bolt B:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. 1GR-FE:
    Install the 9 bolts.

    Torque:
    for bolt A:
    72 N*m{ 730 kgf*cm , 53 ft.*lbf }
    for bolt B:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



3. INSTALL STIFFENER PLATE (for 1KD-FTV)


G034607E05
  1. Install the stiffener plate RH with the 4 bolts.

    Torque:
    72 N*m{ 730 kgf*cm , 53 ft.*lbf }

  1. Install the stiffener plate LH with the 4 bolts.

    Torque:
    72 N*m{ 730 kgf*cm , 53 ft.*lbf }



4. INSTALL EXHAUST MANIFOLD STAY (for 2TR-FE)


B086194E06
  1. Install the exhaust manifold stay with the 3 bolts.

    Torque:
    for bolt A:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }
    for bolt B:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }
    for bolt C:
    72 N*m{ 730 kgf*cm , 53 ft.*lbf }



5. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR


G034226E02
  1. Install the mounting insulator with the 4 bolts.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }



6. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


G034218E05
  1. Install the frame crossmember with the 4 bolts and 4 nuts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Install the 4 set bolts to the No. 1 engine mounting insulator rear.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }



7. INSTALL STARTER ASSEMBLY
  1. Install the starter.
    for 2TR-FE; (Click here)
    for 1GR-FE 1.6 kW Type: (Click here)
    for 1KD-FTV BOSCH made: (Click here)
    for 1KD-FTV DENSO made: (Click here)



8. CONNECT CLUTCH RELEASE CYLINDER ASSEMBLY (except 1GR-FE)


G034223E01
  1. Install the release cylinder with the 2 bolts.

    Torque:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }



9. INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY (for 1GR-FE)


D030416E04
  1. Install the accumulator with the 3 bolts.

    Torque:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }

  1. Using a union nut wrench, connect the 2 flexible hose tubes.

    Torque:
    15.5 N*m{ 158 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque value for situations where a union nut wrench is combined with a torque wrench (Click here).



    C112662
  1. Install the clutch release cylinder with the 2 bolts.

    Torque:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }



    C112616
  1. Using a union nut wrench, connect the flexible tube.

    Torque:
    15.5 N*m{ 158 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque value for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Install the 2 way with the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



    C112615
  1. Using a union nut wrench, install the flexible tube.

    Torque:
    15.5 N*m{ 158 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque value for situations where a union nut wrench is combined with a torque wrench (Click here).



    C112617
  1. Install the release cylinder heat insulator with the bolt and the nut.

    Torque:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }



10. CONNECT WIRE HARNESS
  1. Transmission side:
    Connect the back-up light switch connector.

  1. Transfer side:
    Connect the No. 1, No. 2 and No. 3 transfer indicator switch connectors, and vehicle speed sensor connector.



11. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. Install the front exhaust pipe.
    for 1KD-FTV: (Click here).
    for 2TR-FE: (Click here).
    for 1GR-FE: (Click here).



12. INSTALL REAR PROPELLER SHAFT ASSEMBLY
  1. Install the rear propeller shaft.
    for DANA made: (Click here)
    except DANA made: (Click here)



13. INSTALL FRONT PROPELLER SHAFT ASSEMBLY
(Click here)


14. ADD MANUAL TRANSMISSION OIL


D025304E08

Oil grade:
GL-4

Viscosity:
SAE 75W-90

Standard capacity:
2.2 liters (2.3 US qts, 1.9 Imp. qts)

Torque:
37 N*m{ 377 kgf*cm , 27 ft.*lbf }



15. INSTALL NO. 2 ENGINE UNDER COVER

Torque:
28 N*m{ 286 kgf*cm , 21 ft.*lbf }



16. INSTALL NO. 1 ENGINE UNDER COVER

Torque:
28 N*m{ 286 kgf*cm , 21 ft.*lbf }



17. INSTALL TRANSFER CASE LOWER PROTECTOR
  1. Install the transfer case lower protector with the 4 bolts.

    Torque:
    18 N*m{ 183 kgf*cm , 13 ft.*lbf }



18. INSTALL TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY
  1. Install the transfer shift lever.

    HINT:
    Apply MP grease to the tip of the transfer shift lever.

  1. Using pliers, install the snap ring.



19. INSTALL FLOOR SHIFT SHIFT LEVER ASSEMBLY
  1. Cover the shift lever cap with a cloth.

  1. Press down on the shift lever cap and rotate it clockwise to install it.

    HINT:
    Apply MP grease to the tip of the shift lever.



20. INSTALL SHIFT LEVER BOOT ASSEMBLY


G034544E04
  1. Install the shift lever boot with the 4 screws and 2 clips.



21. INSTALL CONSOLE BOX ASSEMBLY
(Click here)


22. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



23. BLEED AIR FROM CLUTCH PIPE LINE (for 1GR-FE)
(Click here)


24. INSPECT AND ADJUST CLUTCH PEDAL ASSEMBLY (for 1GR-FE)
  1. Inspect and adjust the clutch pedal .



25. CHECK FLUID LEVEL IN RESERVOIR (for 1GR-FE)
  1. Check the fluid level in the reservoir (Click here).



26. CHECK FOR CLUTCH FLUID LEAKAGE (for 1GR-FE)