Home › ENGINE ยท 2KD-FTV › INTAKE › INTAKE MANIFOLD

INTAKE MANIFOLD > REMOVAL

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes, clean them with a brush and compressed air.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE DIESEL THROTTLE BODY ASSEMBLY
(Click here)


4. REMOVE MANIFOLD STAY


A099622E01
  1. Remove the 2 bolts and manifold stay.



5. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE


A099624E01
  1. Remove the engine oil level dipstick.

  1. Remove the bolt and injection pipe clamp.

  1. Remove the bolt and engine oil level dipstick guide.

  1. Remove the O-ring from the engine oil level dipstick guide.



6. REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (for EGR)


    A212373
  1. Disconnect the connector.

  1. Disconnect the 2 vacuum hoses.

  1. Remove the 2 bolts and electric vacuum regulating valve together with the bracket.

    NOTICE:
    Do not remove the electric vacuum regulating valve from the bracket.



7. REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET


    A114779
  1. Remove the 3 bolts and No. 2 intake air connector bracket.



8. REMOVE INTAKE AIR CONNECTOR
  1. Remove the 2 nuts, bolt, intake air connector and gasket.



9. REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY


    A272003E01
  1. Remove the 2 bolts, 2 nuts, No. 1 EGR pipe and 2 gaskets.
    Text in Illustration 
    *1
    Gasket



10. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY
  1. Disconnect the EGR valve position sensor connector.

  1. Remove the electric EGR control valve and gasket.



11. REMOVE NO. 1, No. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
  1. After removing the fuel pipe, cover the outlets on the common rail with tape to keep out foreign matter.
  2. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.



    A231803E02
  1. Remove the bolt and No. 2 injection pipe clamp.
    Text in Illustration 
    *1
    No. 2 Injection Pipe Clamp
    *2
    No. 3 Injection Pipe Clamp
    *a
    Injector Side
    *b
    Common Rail Side

  1. Remove the 2 nuts and No. 3 injection pipe clamp.

  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.



12. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection pipe clamp with a new one.



    A098893E01
  1. Remove the 2 bolts and disconnect the 2 injection pipe clamps.



    A231804E02
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
    Text in Illustration 
    *a
    Injector Side
    *b
    Common Rail Side



13. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
  1. Disconnect the 3 fuel hoses.



    A272915E01
  1. Remove the union bolt, 2 bolts, No. 2 nozzle leakage pipe and gasket.
    Text in Illustration 
    *1
    Union Bolt



14. REMOVE INTAKE MANIFOLD


A131656
  1. Remove the 2 nuts, 4 bolts, intake manifold and gasket.