Home › BODY › INTERIOR › FUEL LID LOCK CONTROL

FUEL LID LOCK CONTROL > REMOVAL

for Preparation Click here



1. REMOVE FRONT SEAT ASSEMBLY LH
  1. for Manual Seat:
    (Click here)

  1. for Power Seat:
    (Click here)



2. REMOVE FRONT SEAT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



3. REMOVE REAR NO. 1 SEAT ASSEMBLY LH
(Click here)


4. REMOVE REAR NO. 1 SEAT ASSEMBLY RH
(Click here)


5. REMOVE REAR NO. 2 SEAT ASSEMBLY LH (w/ Rear No. 2 Seat)
(Click here)


6. REMOVE CONSOLE BOX ASSEMBLY
(Click here)


7. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Remove the tonneau cover.



8. REMOVE TONNEAU COVER HOLDER LH (w/ Tonneau Cover)


B294208
  1. Remove the screw and tonneau cover holder.



9. REMOVE TONNEAU COVER HANGER LH (w/ Tonneau Cover)


B294209
  1. Remove the screw and tonneau cover hanger.



10. REMOVE FRONT DOOR SCUFF PLATE LH


B276926E01
  1. Put protective tape around the front door scuff plate.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 7 claws and 3 clips and remove the front door scuff plate.



11. REMOVE COWL SIDE TRIM BOARD LH


B277609
  1. Remove the part of the front door opening trim attached to the cowl side trim board.

  1. Remove the clip.

  1. Detach the 2 clips and remove the cowl side trim board.



12. REMOVE REAR DOOR SCUFF PLATE LH


B276927E01
  1. Put protective tape around the rear door scuff plate.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 7 claws and 2 clips and remove the rear door scuff plate.



13. REMOVE LOWER CENTER PILLAR GARNISH LH


B277799
  1. Detach the 2 claws and remove the outer lap belt anchor cover.



    B276978
  1. Remove the bolt and disconnect the front seat outer belt floor anchor.



    B276929
  1. Remove the part of the front door opening trim and rear door opening trim weatherstrip attached to the lower center pillar garnish.

  1. Detach the 2 claws, 2 guides and 2 clips and remove the lower center pillar garnish.



14. REMOVE BACK DOOR SCUFF PLATE


B276933
  1. Detach the 4 claws, 2 guides and 6 clips and remove the back door scuff plate.



15. REMOVE QUARTER TRIM HOOK


B276937

HINT:
Use the same procedure for both quarter trim hooks.

  1. Remove the screw and quarter trim hook.



16. REMOVE QUARTER INSIDE TRIM BOARD LH


B277799
  1. Detach the 2 claws and remove the outer lap belt anchor cover.

    HINT:
    Use the same procedure for both outer lap belt anchor covers.



    B277800
  1. Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.



    B277801
  1. w/ Rear No. 2 Seat:

    1. Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.

  1. Remove the part of the rear door opening trim weatherstrip attached to the quarter inside trim board.

  1. Using a clip remover, remove the clip.

  1. Detach the 7 claws and 10 clips.



  1. Disconnect the power point socket connector and remove the quarter inside trim board.


    B276940



17. REMOVE FRONT FLOOR CARPET ASSEMBLY
  1. Partially remove the floor carpet.

    HINT:
    It is not necessary to fully remove the floor carpet. Partially remove it so that the lock control cable can be removed in a later step.



18. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY
  1. Remove the fuel lid lock open lever.



  1. Remove the tape and detach the cable from each of the clamps shown in the illustration.


    B278829E01


    Text in Illustration 
    *1
    Fuel Lid Lock Open Lever
    *2
    Tape



    B277114
  1. Turn the fuel filler opening lid lock retainer counterclockwise and remove the fuel lid lock control cable from the fuel filler opening lid lock retainer.



19. REMOVE FUEL FILLER OPENING LID LOCK RETAINER


B277116
  1. Turn the fuel filler opening lid lock retainer clockwise and remove the fuel filler opening lid lock retainer as shown in the illustration.