OIL PUMP (w/o Glow Plug Controller) > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. DRAIN ENGINE OIL |
Remove the oil filler cap.
Remove the oil drain plug, and drain the engine oil from the oil pan.
| 4. DRAIN ENGINE COOLANT |
![]() |
Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.
Loosen the cylinder block drain cock plug and the radiator drain cock plug.

| 5. REMOVE ENGINE ASSEMBLY |
| 6. REMOVE NO. 1 TIMING BELT COVER |
![]() |
Remove the bolt and water hose clamp.
Remove the wire harness clamp.
Remove the 6 bolts and timing belt cover.
| 7. REMOVE TIMING BELT |
![]() |
Turn the crankshaft clockwise and align the timing marks as shown in the illustration.
![]() |
Uniformly loosen the 2 bolts and remove the timing belt tensioner.
Remove the timing belt.
Using a 10 mm hexagon wrench, remove the bolt, timing belt idler and washer.

| 8. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY |
| 9. REMOVE NO. 2 IDLE PULLEY ASSEMBLY |
Remove the bolt, pulley plate, No. 2 idle pulley and spacer.
| 10. REMOVE GENERATOR ASSEMBLY |
![]() |
Remove the nut and generator wire.
Disconnect the generator connector.
Remove the 2 bolts and generator.
| 11. REMOVE GENERATOR BRACKET |
Remove the bolt and generator bracket.
| 12. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Remove the 4 bolts and V-ribbed belt tensioner.
| 13. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET |
Remove the 4 bolts and No. 1 compressor mounting bracket.
| 14. REMOVE DIESEL THROTTLE BODY ASSEMBLY (w/ EGR Cooler) |
Disconnect the 2 connectors.
![]() |
Remove the 2 bolts, 2 nuts, diesel throttle body and gasket.
| 15. REMOVE MANIFOLD STAY WITH VACUUM SWITCHING VALVE (w/ EGR Cooler) |
Disconnect the 2 vacuum switching valve connectors and the 4 vacuum transmitting hoses.
![]() |
Remove the 2 bolts and manifold stay with vacuum switching valve.
| 16. REMOVE MANIFOLD STAY (w/o EGR Cooler) |
![]() |
Remove the 2 bolts and manifold stay.
| 17. DISCONNECT NO. 3 WATER BY-PASS HOSE (w/ EGR Cooler) |
![]() |
Remove the clamp.
Disconnect the No. 3 water by-pass hose from the EGR cooler.
| 18. DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ EGR Cooler) |
Disconnect the No. 4 water by-pass hose from the EGR cooler.
| 19. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY |
w/ EGR Cooler:
![]() |
Remove the 2 nuts and No. 3 injection pipe clamp.
![]() |
Remove the 2 bolts and 2 No. 2 injection pipe clamps.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
w/o EGR Cooler:
![]() |
Remove the bolt and No. 2 injection pipe clamp.
Remove the 2 nuts and No. 3 injection pipe clamp.
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
| 20. REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET (w/ EGR Cooler) |
![]() |
Remove the 3 bolts and No. 2 intake air connector bracket.
| 21. REMOVE NO. 3 WATER BY-PASS PIPE (w/ EGR Cooler) |
![]() |
Remove the 2 bolts and disconnect the No. 3 water by-pass pipe with wire harness.
| 22. REMOVE NO. 1 GAS FILTER WITH GAS FILTER BRACKET (w/ EGR Cooler) |
![]() |
Disconnect the 2 vacuum hoses.
Remove the bolt and No. 1 gas filter with gas filter bracket.
| 23. REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (w/ EGR Cooler) |
w/ EGR Cooler:
![]() |
Disconnect the connector.
![]() |
Disconnect the 4 vacuum hoses.
![]() |
Remove the 2 bolts and electric vacuum regulating valve with bracket.
w/o EGR Cooler:
![]() |
Disconnect the 2 connectors.
Disconnect the 3 vacuum hoses.
Remove the 2 bolts and electric vacuum regulating valve together with the bracket.
![]() |
Remove the screw and vacuum switching valve.
| 24. REMOVE NO. 2 INTAKE AIR CONNECTOR (w/ EGR Cooler) |
![]() |
Remove the 3 nuts, No. 2 intake air connector and gasket.
| 25. REMOVE INTAKE AIR CONNECTOR (w/ EGR Cooler) |
![]() |
Remove the 3 bolts, intake air connector and 2 gaskets.
| 26. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER (w/ EGR Cooler) |
Disconnect the EGR valve position sensor connector.
![]() |
Disconnect the vacuum hose from the No. 2 EGR valve.
![]() |
Remove the bolt, 2 nuts, electric EGR control valve with No. 2 EGR valve and EGR cooler.
Remove the gasket from the cylinder head.
| 27. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY |
w/ EGR Cooler:
![]() |
Remove the bolt and disconnect the injection pipe clamp.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
w/o EGR Cooler:
![]() |
Remove the 2 bolts and disconnect the 2 injection pipe clamps.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
| 28. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE |
Remove the engine oil level dipstick.
Remove the bolt and injection pipe clamp.
Remove the bolt and engine oil level dipstick guide.
Remove the O-ring engine oil level dipstick guide.
| 29. REMOVE FUEL INLET PIPE SUB-ASSEMBLY |
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.
| 30. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY |
Disconnect the 3 fuel hoses.
![]() |
Remove the union bolt, 3 bolts, No. 2 nozzle leakage pipe and gasket.
| 31. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Remove the 3 bolts and disconnect the 4 connectors.
Disconnect the ventilation hose.
![]() |
Using a small screwdriver, remove the nozzle holder seal by prying between the nozzle holder seal and the cutout part of the cylinder head cover.
![]() |
Remove the 10 bolts, 2 nuts, cylinder head cover and cylinder head cover gasket.
![]() |
Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.
| 32. REMOVE CAMSHAFT TIMING PULLEY |
![]() |
Remove the bolt of the camshaft timing pulley while holding the camshaft with a wrench.
Remove the camshaft timing pulley.
| 33. REMOVE NO. 2 TIMING BELT COVER |
Remove the 4 bolts, nut and timing belt cover.
| 34. REMOVE WATER PUMP ASSEMBLY |
![]() |
Remove the 5 bolts, 2 nuts, water pump and gasket.
| 35. REMOVE TIMING GEAR COVER INSULATOR (w/ EGR Cooler) |
![]() |
Remove the bolt and timing gear cover insulator.
| 36. REMOVE VACUUM PUMP ASSEMBLY |
![]() |
Remove the 2 nuts, vacuum pump and 2 O-rings.
| 37. REMOVE VANE PUMP ASSEMBLY |
![]() |
Remove the 2 nuts, vane pump and O-ring.
| 38. REMOVE CAMSHAFT POSITION SENSOR |
![]() |
Disconnect the camshaft position sensor connector.
Remove the bolt and camshaft position sensor.
| 39. REMOVE CRANKSHAFT POSITION SENSOR |
Disconnect the crankshaft position sensor connector.
Detach the 3 clips, and the bolt and crankshaft position sensor.

| 40. REMOVE PUMP DRIVE SHAFT PULLEY |
![]() |
Remove the 4 bolts, No. 2 camshaft timing pulley flange and pump drive shaft pulley.
![]() |
Using SST, hold the crankshaft pulley and remove the nut and O-ring.
| 41. REMOVE CRANKSHAFT PULLEY |
![]() |
Using SST, hold the crankshaft pulley and loosen the pulley bolt.
![]() |
Using SST, remove the pulley bolt and crankshaft pulley.
| 42. REMOVE TIMING GEAR COVER |
![]() |
Remove the 14 bolts and 2 nuts.
Pry the gear cover in the location shown in the illustration, and remove the gear cover together with the supply pump drive gear.
Remove the O-ring from the timing gear cover.
| 43. REMOVE INJECTION GEAR |
![]() |
Using SST, remove the injection gear.
| 44. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE |
| 45. REMOVE CRANKSHAFT TIMING GEAR |
![]() |
Using SST, remove the crankshaft timing gear.
| 46. REMOVE NO. 1 IDLE GEAR |
![]() |
Secure the idle gears to the idle gear with the service bolt.
Remove the 2 bolts and thrust plate.
Turn the sub-gear and align the gear teeth of the idle main gear and sub-gear.
Remove the idle gear and sub-gear.
Remove the idle gear shaft.
| 47. REMOVE FUEL SUPPLY PUMP ASSEMBLY |
![]() |
Remove the bolt and clamp.
Remove the bolt and oil dipstick guide.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.
![]() |
Disconnect the 2 fuel hoses.
![]() |
Disconnect the 2 connectors.
![]() |
Remove the 4 bolts indicated by the arrows in the illustration.
Remove the No. 2 camshaft timing pulley flange and pump drive shaft pulley.
![]() |
Remove the set nut and O-ring while holding the crankshaft pulley using SST.
![]() |
Loosen the 2 nuts.
![]() |
Using SST, disconnect the pump from the injection gear.
Remove the 2 nuts and pump.
Remove the O-ring.
| 48. REMOVE OIL PAN SUB-ASSEMBLY |
Remove the 4 bolts and oil level gauge sensor.
Remove the 22 bolts and 2 nuts.
![]() |
Insert the blade of an oil pan seal cutter between the oil pan and cylinder block, cut through the applied sealer and remove the oil pan.
| 49. REMOVE OIL STRAINER SUB-ASSEMBLY |
Remove the 2 bolts, 2 nuts, oil strainer and gasket.
| 50. REMOVE TIMING GEAR CASE ASSEMBLY |
![]() |
Remove the union bolt and 8 bolts.
Pry the gear case in the location shown in the illustration, and remove the gear case, driven rotor and gasket.
Remove the 2 O-rings.