POWER STEERING LINK > INSTALLATION |
| 1. INSTALL TIE ROD END SUB-ASSEMBLY LH |
Screw the lock nut and tie rod end onto the rack end until the matchmarks are aligned.
After adjusting toe-in, torque the nut.
| 2. INSTALL TIE ROD END SUB-ASSEMBLY RH |
| 3. INSTALL POWER STEERING LINK ASSEMBLY |
![]() |
Install the steering link with the 2 bolts and 2 nuts.
| 4. INSTALL STABILIZER BAR FRONT |
Install the stabilizer bar front to the vehicle body.
| 5. STABILIZE SUSPENSION |
| 6. CONNECT STEERING GEAR OUTLET RETURN TUBE |
![]() |
Using a union nut wrench, connect the outlet return tube.
![]() |
Install the hose with the clip.
| 7. CONNECT PRESSURE FEED TUBE ASSEMBLY |
![]() |
Install the pressure feed tube to the steering link with the bolt.
![]() |
Using a union nut wrench, tighten the flare nut and connect the pressure feed tube.
| 8. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY |
Align the matchmarks on the steering intermediate shaft and steering link.
Install the bolt.
| 9. CONNECT STEERING SLIDING YOKE |
![]() |
Align the matchmarks on the steering sliding yoke and steering intermediate shaft, and connect the steering sliding yoke to the steering intermediate shaft.
Install the bolt labeled B.
Tighten the bolt labeled A.
| 10. CONNECT TIE ROD END SUB-ASSEMBLY LH |
Connect the tie rod end to the steering knuckle arm with the nut.
Install a new cotter pin.
| 11. CONNECT TIE ROD END SUB-ASSEMBLY RH |
| 12. INSTALL FRONT STABILIZER BAR |
Install the stabilizer bar front to the vehicle body.
| 13. INSTALL FRONT SIDE MEMBER TO FRONT SUSPENSION CROSSMEMBER BRACE |
Install the crossmember brace with the 8 bolts.
| 14. INSTALL NO. 1 ENGINE UNDER COVER |
Install the under cover with the 4 bolts.
| 15. INSTALL NO. 2 ENGINE UNDER COVER |
Install the under cover with the 4 bolts.
| 16. INSTALL FRONT WHEEL |
| 17. PLACE FRONT WHEELS FACING STRAIGHT AHEAD |
| 18. INSTALL WINDSHIELD WIPER SWITCH ASSEMBLY |
Attach the claw to install the windshield wiper switch.
Connect the connectors.
| 19. INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY |
![]() |
Install the headlight dimmer switch assembly to the steering column, making sure that the stopper protrusions and cutout parts align.
![]() |
Using needle-nose pliers, install the band clamp as shown in the illustration.
Connect the connector.
| 20. INSTALL SPIRAL CABLE SUB-ASSEMBLY |
| 21. INSTALL STEERING COLUMN COVER UPPER |
| 22. INSTALL STEERING COLUMN COVER LOWER |
for Automatic Air Conditioning System:
Connect the room temperature sensor.
Attach the 2 guides to install the lower instrument panel.
Connect the connectors and attach the clamps.
Connect the hood lock control cable, fuel lid lock control cable and DLC3.
Install the 2 bolts <C>, nut <D> and 3 screws <E>.
Install the 2 clips <B>.

| *1 | Clip <B> | *2 | Bolt <C> |
| *3 | Nut <D> | *4 | Screw <E> |
| *5 | Hood Lock Control Cable | *6 | Fuel Lid Lock Control Cable |
| *7 | DLC3 | *8 | Clamp |
| *9 | Guide | - | - |
| 23. INSTALL STEERING WHEEL ASSEMBLY |
![]() |
Align the matchmarks on the steering wheel and main shaft.
Install the steering set nut.
| 24. INSPECT STEERING WHEEL CENTER POINT |
| 25. INSTALL STEERING PAD ASSEMBLY |
With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.
Make sure that the horn sounds.
If the horn does not sound, inspect the horn system.
| 26. INSPECT STEERING PAD ASSEMBLY |
With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.
Make sure that the horn sounds.
If the horn does not sound, inspect the horn system.
| 27. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 28. PERFORM INITIALIZATION |
Perform initialization (Click here).
| 29. CHECK SRS WARNING LIGHT |
Check the SRS warning light (Click here).
| 30. ADD POWER STEERING FLUID |
| 31. BLEED AIR FROM POWER STEERING SYSTEM |
Check the fluid level.
Jack up the front of the vehicle and support it with stands.
Turn the steering wheel.
With the engine stopped, turn the steering wheel slowly from lock to lock several times.
Lower the vehicle.
Start the engine. Run the engine at idle for a few minutes.
Turn the steering wheel.
With the engine idling, turn the steering wheel to the left or right full lock position and hold it there for 2 to 3 seconds. Then turn the steering wheel to the opposite full lock position and hold it there for 2 to 3 seconds.
Repeat the step above several times.
Stop the engine.
![]() |
Check for foaming or emulsification. If the system has to be bled twice because of foaming or emulsification, check for fluid leaks in the system.
Check the fluid level.
| 32. CHECK FOR POWER STEERING FLUID LEAKAGE |
| 33. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |
Inspect and adjust front wheel alignment (Click here).