DTC P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state. | The throttle motor activation duty is more than a specified value for 30 seconds (1 trip detection logic). |
|
| DTC No. | Data List |
| P0488 | Actual Throttle Position |
| Condition | Throttle Valve Position |
| Moment when accelerator pedal is depressed further or released at 3000 rpm | Throttle valve opening angle varies smoothly |


| 1.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR POWER SOURCE) |
![]() |
Disconnect the throttle control motor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| T2-2 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Throttle Control Motor) |
Reconnect the throttle control motor connector.
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT) |
Disconnect the throttle control motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T2-3 (RSC) - Body ground | Always | Below 1 Ω |
Reconnect the throttle control motor connector.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM) |
Disconnect the throttle control motor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T2-1 (RSO) - E6-4 (LUSL) | Always | Below 1 Ω |
| T2-1 (RSO) or E6-4 (LUSL) - Body ground | Always | 10 kΩ or higher |
Reconnect the throttle control motor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 4.REPLACE DIESEL THROTTLE BODY ASSEMBLY |
Replace the diesel throttle body assembly (Click here).
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0488) |
Clear the DTCs (Click here).
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Start the engine.
Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm and lower it.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P0488 is output | A |
| No DTC is output | B |
|
| ||||
| A | |
| 6.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 7.REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE CONTROL MOTOR - BATTERY) |
Repair or replace the harness or connector.
|
| ||||
| 8.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for 30 seconds or more.
Start the engine.
Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm, and then lower it.
Confirm that the DTC is not output again.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTC P0488.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm again, and then idle the engine for 5 minutes.
| NEXT | ||
| ||