DTC P1271 Fuel Regulator Circuit Malfunction (EDU Drive) |
DTC P1272 Fuel Pressure Regulator Malfunction |


| DTC No. | DTC Detection Condition | Trouble Area |
| P1271 | Open or short in pressure discharge valve circuit. There is no valve opening confirmation (IJF) signal from EDU to ECM despite the ECM sending valve opening command (PRD) signal after the engine is started. (1 trip detection logic) |
|
| P1272 | Pressure discharge valve closed malfunction. Actual pressure decreasing rate deviates from the simulated pressure decreasing rate after the ignition switch is turned OFF. (2 trip detection logic) |
|
| Engine Speed | Fuel Pressure |
| Idling | Approximately 28000 to 40000 kPa |
| 3000 rpm (No engine load) | Approximately 30000 to 60000 kPa |


| Malfunction Point | Trouble Area |
| A |
|
| B (If A is normal) |
|
| C (If A and B are normal) |
|
| D (If A, B and C are normal) |
|
| Required sensor | EDU |
| Frequency of operation | Continuous |
| Duration | 3 seconds |
| MIL operation | 1 driving cycle |
| Required sensors | Fuel pressure sensor |
| Frequency of operation | Once per driving cycle |
| Duration | 1 second |
| MIL operation | 2 driving cycles |
| Specification |
| Drive the vehicle at 50 km/h (31 mph) in 3rd gear and then decelerate by completely releasing the accelerator pedal |
| Item | Specification | |
| Minimum | Maximum | |
| Fuel pressure | 30000 kPa (306 kgf/cm2, 4,351 psi) | - |
| Fuel temperature | 0°C (32°F) | - |
| Battery voltage | 11 V | - |
| The monitor will not run if the fuel pressure sensor, pressure discharge valve circuit, or fuel temperature sensor is malfunctioning | ||
| Specification |
| There are no confirmation signals from the EDU, despite the ECM sending the command signals regularly during deceleration |
| Specification |
| The internal pressure stays beyond the specified level after the ignition switch was turned OFF |

| 1.READ DTC OUTPUT (DTC P1271 AND/OR P1272) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display (DTC output) | Proceed to |
| P1271 and/or P1272 | A |
| P1272 | B |
|
| ||||
| A | |
| 2.INSPECT COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE) |
![]() |
Disconnect the pressure discharge valve connector.
Measure the resistance of the pressure discharge valve.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 0.85 to 1.05 Ω |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (PRESSURE DISCHARGE VALVE - EDU) |
![]() |
Disconnect the EDU connectors.
Disconnect the pressure discharge valve connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| I14-4 (RLF+) - P21-2 | Below 1 Ω |
| I15-1 (RLF-) - P21-1 | Below 1 Ω |
| I14-4 (RLF+) or P21-2 - Body ground | 10 kΩ or higher |
| I15-1 (RLF-) or P21-1 - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| I21-4 (RLF+) - P21-2 | Below 1 Ω |
| I15-1 (RLF-) - P21-1 | Below 1 Ω |
| I21-4 (RLF+) or P21-2 - Body ground | 10 kΩ or higher |
| I15-1 (RLF-) or P21-1 - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (ECM - EDU) |
![]() |
Disconnect the EDU connectors.
Disconnect the ECM connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| E7-32 (PRD) - I16-2 (PRD) | Below 1 Ω |
| E7-25 (INJF) - I16-5 (INJF) | Below 1 Ω |
| E7-32 (PRD) or I16-2 (PRD) - Body ground | 10 kΩ or higher |
| E7-25 (INJF) or I16-5 (INJF) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.INSPECT INJECTOR DRIVER (BATTERY VOLTAGE) |
![]() |
Disconnect the EDU connector.
Turn the ignition switch ON.
Measure the voltage of the EDU connector.
| Tester Connection | Specified Condition |
| I14-2 (+B) - I14-3 (GND) | 11 to 14 V |
| Tester Connection | Specified Condition |
| I21-2 (+B) - I14-3 (GND) | 11 to 14 V |
|
| ||||
| OK | |
| 6.INSPECT ECM (PRD VOLTAGE) |
![]() |
Inspect the ECM using the oscilloscope.
Drive the vehicle at 50 km/h (31 mph) in the third gear, and then decelerate by releasing the accelerator pedal.
Check the waveform between the terminal of the E6 and E7 ECM connectors.
| Tester Connection | Specified Condition |
| E7-32 (PRD) - E6-7 (E1) | Correct waveform shown |
|
| ||||
| OK | |
| 7.REPLACE INJECTOR DRIVER |
Replace the injector driver (Click here).
| NEXT | |
| 8.CHECK IF DTC OUTPUT RECURS (DTC P1271 AND/OR P1272) |
| NEXT | ||
| ||
| 9.REPLACE COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE) |
Replace common rail assembly (Click here).
| NEXT | |
| 10.CHECK IF DTC OUTPUT RECURS (DTC P1271 AND/OR P1272) |
| NEXT | ||
| ||