COMMON RAIL (w/o Glow Plug Controller) > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE DIESEL THROTTLE BODY ASSEMBLY (w/ EGR Cooler) |
| 4. REMOVE INTERCOOLER ASSEMBLY (w/o EGR Cooler) |
| 5. REMOVE NO. 1 ENGINE UNDER COVER |
| 6. REMOVE NO. 2 ENGINE UNDER COVER |
| 7. DRAIN ENGINE COOLANT (w/ EGR Cooler) |
![]() |
Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.
Loosen the cylinder block drain cock plug and the radiator drain cock plug.

| 8. DRAIN ENGINE OIL |
Remove the oil filler cap.
Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.
Wipe the oil pan and drain plug.
Install a new gasket and the oil pan drain plug.
| 9. REMOVE MANIFOLD STAY WITH VACUUM SWITCHING VALVE (w/ EGR Cooler) |
Disconnect the 2 vacuum switching valve connectors and the 4 vacuum transmitting hoses.
![]() |
Remove the 2 bolts and manifold stay with vacuum switching valve.
| 10. REMOVE MANIFOLD STAY (w/o EGR Cooler) |
![]() |
Remove the 2 bolts and manifold stay.
| 11. REMOVE OIL FILTER SUB-ASSEMBLY |
![]() |
Using SST, remove the oil filter.
| 12. DISCONNECT NO. 3 WATER BY-PASS HOSE (w/ EGR Cooler) |
![]() |
Remove the clamp.
Disconnect the No. 3 water by-pass hose from the EGR cooler.
| 13. DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ EGR Cooler) |
Disconnect the No. 4 water by-pass hose from the EGR cooler.
| 14. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY |
w/ EGR Cooler:
![]() |
Remove the 2 nuts and No. 3 injection pipe clamp.
![]() |
Remove the 2 bolts and 2 No. 2 injection pipe clamps.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
w/o EGR Cooler:
![]() |
Remove the bolt and No. 2 injection pipe clamp.
Remove the 2 nuts and No. 3 injection pipe clamp.
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
| 15. REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET (w/ EGR Cooler) |
![]() |
Remove the 3 bolts and No. 2 intake air connector bracket.
| 16. DISCONNECT NO. 3 WATER BY-PASS PIPE (w/ EGR Cooler) |
![]() |
Remove the 2 bolts and disconnect the No. 3 water by-pass pipe with wire harness.
| 17. REMOVE NO. 1 GAS FILTER WITH GAS FILTER BRACKET (w/ EGR Cooler) |
![]() |
Disconnect the 2 vacuum hoses.
Remove the bolt and No. 1 gas filter with gas filter bracket.
| 18. REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (w/ EGR Cooler) |
w/ EGR Cooler:
![]() |
Disconnect the connector.
![]() |
Disconnect the 4 vacuum hoses.
![]() |
Remove the 2 bolts and electric vacuum regulating valve with bracket.
w/o EGR Cooler:
![]() |
Disconnect the 2 connectors.
Disconnect the 3 vacuum hoses.
Remove the 2 bolts and electric vacuum regulating valve together with the bracket.
![]() |
Remove the screw and vacuum switching valve.
| 19. REMOVE NO. 2 INTAKE AIR CONNECTOR (w/ EGR Cooler) |
![]() |
Remove the 3 nuts, No. 2 intake air connector and gasket.
| 20. REMOVE INTAKE AIR CONNECTOR (w/ EGR Cooler) |
![]() |
Remove the 3 bolts, intake air connector and 2 gaskets.
| 21. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER (w/ EGR Cooler) |
Disconnect the EGR valve position sensor connector.
![]() |
Disconnect the vacuum hose from the No. 2 EGR valve.
![]() |
Remove the bolt, 2 nuts, electric EGR control valve with No. 2 EGR valve and EGR cooler.
Remove the gasket from the cylinder head.
| 22. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY |
w/ EGR Cooler:
![]() |
Remove the bolt and disconnect the injection pipe clamp.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
w/o EGR Cooler:
![]() |
Remove the 2 bolts and disconnect the 2 injection pipe clamps.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
| 23. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY |
Disconnect the 3 fuel hoses.
![]() |
Remove the union bolt, 3 bolts, No. 2 nozzle leakage pipe and gasket.
| 24. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE |
Remove the engine oil level dipstick.
Remove the bolt and injection pipe clamp.
Remove the bolt and engine oil level dipstick guide.
Remove the O-ring engine oil level dipstick guide.
| 25. REMOVE FUEL INLET PIPE SUB-ASSEMBLY |
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.
| 26. REMOVE COMMON RAIL ASSEMBLY |
Disconnect the 2 connectors.
![]() |
Remove the 2 bolts, common rail and No. 2 intake manifold insulator.