DTC P1271 Fuel Regulator Circuit Malfunction (EDU Drive) |
DTC P1272 Fuel Pressure Regulator Malfunction |


| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON to off and Drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal | Either condition is met (1 trip detection logic):
|
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON to off | Pressure discharge valve does not open. Actual pressure decreasing rate deviates from the simulated pressure decreasing rate after the ignition switch is turned off (2 trip detection logic). |
|
| DTC No. | Data List |
| P1271 |
|
| P1272 |
| Engine Speed | Fuel Pressure (kPa) |
| Idling | Fuel press is within 5000 kPa of Target Common Rail Pressure |
| 2500 rpm (No engine load) |

| Required sensors | Injector driver |
| Frequency of operation | Continuous |
| Duration | 3 seconds |
| MIL operation | 1 driving cycle |
| Required sensors | Fuel pressure sensor |
| Frequency of operation | Once per driving cycle |
| Duration | 1 second |
| MIL operation | 2 driving cycles |
| Specification |
| The vehicle is driven at 50 km/h (31 mph) in 3rd gear, and then decelerated by complete release of the accelerator pedal 3 times. |
| Item | Specification | |
| Minimum | Maximum | |
| Fuel pressure | 27000 kPa (275 kgf/cm2, 3915 psi) | - |
| Fuel temperature | 0°C (32°F) | - |
| Battery voltage | 11 V | - |
| The monitor will not run if the fuel pressure sensor, pressure discharge valve circuit or fuel temperature sensor is malfunctioning. | ||
| Specification |
| There are no confirmation signals from the injector driver for a specific number of times consecutively, despite the ECM sending command signals regularly during deceleration. |
| Specification |
| The internal pressure stays beyond the specified level after the ignition switch is turned off. |

| 1.CHECK IF DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the pending DTCs.
| Result | Proceed to |
| P1272 | A |
| P1271 | B |
| P1271 and P1272 | B |
| Other DTCs output | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE OPERATION) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain /Engine / Utility / Pressure Discharge Valve Check (Click here).
Select "Close to Open Check".
Read the value of "Open and Engine OFF".
|
| ||||
|
| ||||
| 3.INSPECT COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE RESISTANCE) |
Inspect the common rail assembly (Click here).
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (PRESSURE DISCHARGE VALVE - INJECTOR DRIVER) |
Disconnect the injector driver connector.
Disconnect the pressure discharge valve connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P22-2 - I14-4 (RLF+) | Always | Below 1 Ω |
| P22-1 - I15-1 (RLF-) | Always | Below 1 Ω |
| P22-2 or I14-4 (RLF+) - Body ground | Always | 10 kΩ or higher |
| P22-1 or I15-1 (RLF-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| P22-2 - I21-4 (RLF+) | Always | Below 1 Ω |
| P22-1 - I15-1 (RLF-) | Always | Below 1 Ω |
| P22-2 or I21-4 (RLF+) - Body ground | Always | 10 kΩ or higher |
| P22-1 or I15-1 (RLF-) - Body ground | Always | 10 kΩ or higher |
Reconnect the injector driver connector.
Reconnect the pressure discharge valve connector.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (ECM - INJECTOR DRIVER) |
Disconnect the injector driver connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I16-2 (PRD) - E7-32 (PRD) | Always | Below 1 Ω |
| I16-5 (INJF) - E7-25 (INJF) | Always | Below 1 Ω |
| I16-2 (PRD) or E7-32 (PRD) - Body ground | Always | 10 kΩ or higher |
| I16-5 (INJF) or E7-25 (INJF) - Body ground | Always | 10 kΩ or higher |
Reconnect the injector driver connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 6.INSPECT INJECTOR DRIVER (POWER SOURCE CIRCUIT) |
![]() |
Disconnect the injector driver connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| I14-2 (+B) - I14-3 (GND) | Ignition switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| I21-2 (+B) - I21-3 (GND) | Ignition switch ON | 11 to 14 V |
| *A | for Manual Transmission |
| *B | for Automatic Transmission |
| *a | Front view of wire harness connector (to Injector Driver) |
Reconnect the injector driver connector.
|
| ||||
| OK | |
| 7.REPLACE INJECTOR DRIVER |
Replace the injector driver (Click here).
| NEXT | |
| 8.CHECK IF DTC OUTPUT RECURS (DTC P1271 AND/OR P1272) |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the pending DTCs.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTC P1271 and P1272.
Check the DTC judgment result.
| Tester Display | Result | Proceed to |
| Pending DTC | P1271 and/or P1272 is output | B |
| All Readiness | NORMAL | A |
| ABNORMAL | B |
|
| ||||
| A | ||
| ||
| 9.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
|
| ||||
| 10.GO TO INJECTOR CIRCUIT |
Go to injector circuit (Click here).
|
| ||||
| 11.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 12.REPLACE COMMON RAIL ASSEMBLY |
Replace the common rail assembly (Click here).
| NEXT | |
| 13.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the pending DTC is not output again.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTC P1271 and P1272.
Check the DTC judgment result.
| NEXT | ||
| ||