Home › ENGINE · 1KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (w/o EGR Cooler)

DTC    P2121    Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance

for Preparation Click here


DESCRIPTION

Refer to DTC P2120 (Click here).

DTC No.
DTC Detection Condition
Trouble Area
P2121
Condition (a) continues for 2 seconds:
(a) Difference between VPA1 and VPA2 exceeds the threshold
(1 trip detection logic)
  1. Accelerator pedal position sensor circuit
  2. Accelerator pedal position sensor
  3. ECM

WIRING DIAGRAM

Refer to DTC P2120 .

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.READ VALUE USING INTELLIGENT TESTER (ACCEL SENS. NO.1 VOLT % AND ACCEL SENS. NO.2 VOLT %)


    FI07052E07
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.

  1. Read the values.

    Standard:
    Accelerator Pedal
    Accel Sens. No.1 Volt %
    Accel Sens. No.2 Volt %
    Released
    10 to 22%
    24 to 40%
    Depressed
    52 to 90%
    68 to 99%



OK
REPLACE ECM (Click here)
NG


2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)


    A099833E14
  1. Disconnect the A22 sensor connector.

  1. Disconnect the E4 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    VCP2 (A22-1) - VCP2 (E4-27)
    Below 1 Ω
    EPA2 (A22-2) - EPA2 (E4-29)
    Below 1 Ω
    VPA2 (A22-3) - VPA2 (E4-23)
    Below 1 Ω
    VCPA (A22-4) - VCPA (E4-26)
    Below 1 Ω
    EPA (A22-5) - EPA (E4-28)
    Below 1 Ω
    VPA (A22-6) - VPA (E4-22)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    VCP2 (A22-1) or VCP2 (E4-27) - Body ground
    10 kΩ or higher
    EPA2 (A22-2) or EPA2 (E4-29) - Body ground
    10 kΩ or higher
    VPA2 (A22-3) or VPA2 (E4-23) - Body ground
    10 kΩ or higher
    VCPA (A22-4) or VCPA (E4-26) - Body ground
    10 kΩ or higher
    EPA (A22-5) or EPA (E4-28) - Body ground
    10 kΩ or higher
    VPA (A22-6) or VPA (E4-22) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY
  1. Replace the accelerator pedal rod assembly (Click here).


NEXT


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 15 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P2121
    A
    No output
    B



B
SYSTEM OK
A

REPLACE ECM (Click here)