INTAKE SYSTEM (w/ Glow Plug Controller) > ON-VEHICLE INSPECTION |
| 1. INSPECT INTAKE SYSTEM |
Check that there is no air suction or leaks at the points shown in the illustration.

| *1 | Air Cleaner | *2 | Mass Air Flow Meter |
| *3 | Turbocharger | *4 | Ventilation Pipe |
| *5 | EGR Cooler | *6 | No. 2 EGR Valve |
| *7 | Vacuum Switching Valve (for EGR By-pass Valve) | *8 | Intercooler |
| *9 | Intake Air Temperature Sensor | *10 | Diesel Throttle Body |
| *11 | Manifold Absolute Pressure Sensor | *12 | Electric EGR Control Valve |
| *13 | No. 1 Vacuum Switching Valve (for Swirl Control Valve) | *14 | No. 2 Vacuum Switching Valve (for Swirl Control Valve) |
| *15 | Vacuum Pump | - | - |
| 2. CHECK INTAKE AIR CONTROL SYSTEM |
Check for leakage or clogging between the air cleaner housing and turbocharger inlet and between the turbocharger outlet and cylinder head.
| Condition | Operation |
| Clogged air cleaner | Clean or replace element |
| Hoses collapsed or deformed | Repair or replace |
| Leakage from connections | Check each connection and repair |
| Cracks in components | Check and repair or replace |
| 3. CHECK EXHAUST SYSTEM |
Check for leakage or clogging between the cylinder head and turbocharger inlet and between the turbocharger outlet and exhaust pipe.
| Condition | Operation |
| Deformed components | Repair or replace |
| Foreign material in passages | Remove |
| Leakage from components | Repair or replace |
| Cracks in components | Check and repair or replace |
| 4. CHECK BOOST PRESSURE |
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
![]() |
Take a snapshot of the Data List items with the intelligent tester as shown in the illustration.
| *1 | Snapshot Record Button |
Compare MAP with Target Booster Pressure.
Warm up the engine.
![]() |
Using a 3-way connector, connect SST (turbocharger pressure gauge) between the manifold absolute pressure sensor and gas filter.
| *1 | Manifold Absolute Pressure Sensor |
| *2 | 3-Way Connector |
| *3 | Gas Filter |
Move the shift lever to P or N, and then fully depress the accelerator pedal. Measure the boost pressure at maximum engine speed (4450 to 4750 rpm).
Chart showing the suspected trouble areas when the pressure is below the standard.
| Item | MAP (Absolute pressure inside intake manifold) | MAF (Intake air flow rate) | Accel Position | Actual Throttle Position | Actual EGR Valve Position | EGR Close Lrn. Status (EGR valve fully closed position learning status) | Fuel Pressure | Injection Feedback Val #1 (to #4) |
| Values taken from an actual normal vehicle *1 | - | 150 g/sec. | 100% | 0% | 0% | OK | - | -3 to +3 mm3/st |
| Values which represent a malfunction *1 | MAP is below Target Booster Pressure by 25 kPa or more | MAF is less than 90 g/sec. | Accel Position is less than 90% | Actual Throttle Position is not within 5% of Target Throttle Position | Actual EGR Valve Position is not within 5% of Target EGR Valve Position | NG (Determined after performing learning) | Fuel Pressure is below Target Common Rail Pressure by 10 MPa or more (Check while condition steady) | Outside of above range |
| Turbocharger | ○ | ○ | - | - | - | - | - | - |
| EGR valve does not close or has problem with movement | ○ | ○ | - | - | ○ (Problem with EGR valve movement) *2 | ○ (EGR valve does not close) *2 | - | - |
| Problem with diesel throttle movement | ○ (Intake airflow decreases) | ○ | - | ○ | - | - | - | - |
| Accelerator pedal cannot be fully depressed or problem with accelerator pedal position sensor exists | - | ○ | ○ | - | - | - | - | - |
| Intake air system leakage or blockage | ○ | ○ | - | - | - | - | - | - |
| Exhaust gas leakage before turbocharger or blockage | ○ | ○ | - | - | - | - | - | - |
| Manifold absolute pressure sensor | ○ | ○ | - | - | - | - | - | - |
| Manifold absolute pressure sensor hose is disconnected | ○ | ○ | - | - | - | - | - | - |
| Mass air flow meter sub-assembly | - | ○ | - | - | - | - | - | - |
| Fuel system (injector, supply pump or common rail) | ○ | ○ | - | - | - | - | ○ (Fuel injector leakage, decrease in pressure discharge valve relief pressure or valve is stuck) | ○ *3 |
| 5. INSPECT MANIFOLD ABSOLUTE PRESSURE SENSOR |
Inspect the power source voltage.
Disconnect the manifold absolute pressure sensor connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 3 VC (+) - 1 E (-) | Ignition switch ON | 4.75 to 5.25 V |
| *a | Front view of wire harness connector (to Manifold Absolute Pressure Sensor) |
Connect the manifold absolute pressure sensor connector.
Check the power supply.
Turn the ignition switch to ON.
Disconnect the vacuum hose from the manifold absolute pressure sensor.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E30-12 (PIM +) - E30-6 (EPIM -) | 13.3 kPa (100 mmHg, 3.94 in.Hg) | 0.8 to 1.4 V |
| 26.6 kPa (199 mmHg, 7.85 in.Hg) | 0.5 to 1.0 V | |
| 40 kPa (300 mmHg, 11.81 in.Hg) | 0.3 to 0.9 V |
| *a | Component with harness connected (ECM) |
![]() | Vacuum |
![]() |
Using SST, measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E30-12 (PIM +) - E30-6 (EPIM -) | 19.6 kPa (0.20 kgf/cm2, 2.84 psi) | 1.0 to 1.7 V |
| 39.2 kPa (0.40 kgf/cm2, 5.69 psi) | 1.3 to 1.9 V | |
| 58.8 kPa (0.60 kgf/cm2, 8.53 psi) | 1.5 to 2.2 V | |
| 78.5 kPa (0.80 kgf/cm2, 11.4 psi) | 1.8 to 2.4 V | |
| 98.0 kPa (1.00 kgf/cm2, 14.2 psi) | 2.1 to 2.7 V |
| *a | Component with harness connected (ECM) |
![]() | Pressure |
| 6. CHECK MOTOR FOR TURBOCHARGER CONTROL OPERATION |
Remove the No. 1 exhaust manifold heat insulator and No. 1 turbo insulator .
Check the stroke.
Turn the ignition switch from ON to off.
Check the DC motor operation. Check that the motor rod stroke is as shown in A to C in the illustration below.
After the DC motor operates, visually check that the vane actuation link contacts the fully closed stopper.

| *1 | Motor Rod Stroke | *2 | Ignition Switch |
| *3 | Ignition Switch Off Time | *4 | Motor Rod |
| *5 | Lock Nut | *6 | Fully Closed Stopper |
| *a | Fully Closed Stopper Contact | - | - |