Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM (w/ Jam Protection Function)

POWER WINDOW CONTROL SYSTEM (w/ Jam Protection Function) > Auto Up / Down Function does not Operate

for Preparation Click here


DESCRIPTION


WIRING DIAGRAM

If the AUTO UP / DOWN function does not operate, the cause may be one or more of the following:
  1. The recorded power window fully closed position, which is stored in the power window regulator master switch, was erased as a result of: 1) the DOOR fuse, ECU-IG & GAUGE fuse or IG1 relay being replaced; or 2) the battery cable and the master switch's connector being disconnected.
  2. The master switch has a malfunction.
  3. The pulse sensors in the driver side power window regulator motor have a malfunction.
  4. The wiring between the master switch and the driver side power window regulator motor is open or short-circuited.

B062902E25


INSPECTION PROCEDURE

1.CHECK MANUAL UP / DOWN FUNCTION (FOR DRIVER SIDE)
  1. Check that the manual UP / DOWN function operates normally.

    OK:
    Manual UP / DOWN function operates normally.



NG
GO TO DRIVER SIDE POWER WINDOW MANUAL FUNCTION DOES NOT OPERATE WITH POWER WINDOW MASTER SWITCH (Click here)
OK


2.CHECK LIGHT OF MASTER SWITCH
  1. Turn the ignition switch ON.



  1. Operate the master switch's driver side window switch for 2 seconds or more.


    B144131E01



  1. Check the blinking pattern of the AUTO light. Compare the blinking pattern with the illustration.


    B105775E06

    Result 
    Blinking Pattern
    Proceed to
    1 or 3
    A
    2
    B
    4
    C



B
Go to step 4

C
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
A


3.RESET POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER SIDE)
  1. Check that the power window operates normally after reset (Click here).

    OK:
    Power window operates normally.



OK
END
NG


4.CHECK WIRE HARNESS (MASTER SWITCH - MOTOR (FOR DRIVER SIDE))

B117125E29

  1. Disconnect the P6 master switch connector.

  1. Disconnect the P7 motor connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    P6-3 (VCC) - P7-4 (SSRB)
    Below 1 Ω
    P6-14 (PLS) - P7-5 (PLS)
    Below 1 Ω
    P6-17 (PLS2) - P7-3 (PLS2)
    Below 1 Ω
    P6-2 (GND) - P7-6 (E)
    Below 1 Ω
    P6-3 (VCC) or P7-4 (SSRB) - Body ground
    10 kΩ or higher
    P6-14 (PLS) or P7-5 (PLS) - Body ground
    10 kΩ or higher
    P6-17 (PLS2) or P7-3 (PLS2) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (PLS, PLS2 SIGNAL)
B117126E38
  1. Remove the power window regulator master switch assembly with its connectors still connected.

  1. Using an oscilloscope, check the waveform.

    OK:
    Tester Connection
    Condition
    Specified Condition
    P6-14 (PLS) - Body ground
    Ignition switch ON, driver side power window switch OFF → UP or DOWN
    Pulse waveform is output
    P6-17 (PLS2) - Body ground



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY