Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

DTC    11    Room Temperature Sensor Circuit

for Preparation Click here


DESCRIPTION

The cooler thermistor is installed in the instrument panel to detect the room temperature and control the heater and air conditioning AUTO function. The resistance of the cooler thermistor changes in accordance with the room temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.
The air conditioning amplifier assembly applies voltage (5 V) to the cooler thermistor and reads voltage changes as the resistance of the cooler thermistor changes.

DTC Code
DTC Detection Condition
Trouble Area
11
An open or short in the room temperature sensor circuit.
  1. Cooler thermistor
  2. Air conditioning amplifier assembly
  3. Harness or connector

WIRING DIAGRAM


E227733E08


INSPECTION PROCEDURE

1.INSPECT COOLER THERMISTOR


    E236055E01
  1. Remove the cooler thermistor (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    10°C (50°F)
    3.00 to 3.73 kΩ
    15°C (59°F)
    2.45 to 2.88 kΩ
    20°C (68°F)
    1.95 to 2.30 kΩ
    25°C (77°F)
    1.60 to 1.80 kΩ
    30°C (86°F)
    1.28 to 1.47 kΩ
    35°C (95°F)
    1.00 to 1.22 kΩ
    40°C (104°F)
    0.80 to 1.00 kΩ
    45°C (113°F)
    0.65 to 0.85 kΩ
    50°C (122°F)
    0.50 to 0.70 kΩ
    55°C (131°F)
    0.44 to 0.60 kΩ
    60°C (140°F)
    0.36 to 0.50 kΩ

    Text in Illustration 
    *a
    Resistance (kΩ)
    *b
    Temperature

    NOTICE:
    1. Even slightly touching the cooler thermistor may change the resistance value. Be sure to hold the connector of the cooler thermistor.
    2. When measuring the resistance, the cooler thermistor temperature must be the same as the ambient temperature.

    HINT:
    As the temperature increases, the resistance decreases (Refer to the graph).



NG
REPLACE COOLER THERMISTOR (Click here)
OK


2.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


    E225456E31
  1. Remove the air conditioning amplifier assembly with its connectors still connected (Click here).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A43-18 (TR) - A43-13 (SG-3)
    1. Ignition switch ON
    2. Cabin temperature 25°C (77°F)
    1.8 to 2.2 V
    1. Ignition switch ON
    2. Cabin temperature 40°C (104°F)
    1.2 to 1.6 V

    Text in Illustration 
    *a
    Component with harness connected
    (Air Conditioning Amplifier Assembly)

    HINT:
    As the temperature increases, the voltage decreases.

    Result 
    Result
    Proceed to
    OK (When troubleshooting according to problem symptoms table.)
    A
    OK (When troubleshooting according to DTC.)
    B
    NG
    C



B
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

C
Go to step 3
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - COOLER THERMISTOR)
  1. Disconnect the A43 air conditioning amplifier assembly connector.

  1. Disconnect the A17 cooler thermistor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A43-18 (TR) - A17-2
    Always
    Below 1 Ω
    A43-13 (SG-3) - A17-1
    A43-18 (TR) - Body ground
    Always
    10 kΩ or higher
    A43-13 (SG-3) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)