ROOF HEADLINING > INSTALLATION |
| 1. INSTALL REAR NO. 3 SIDE RAIL SPACER LH |
Attach the 3 claws to install the rear No. 3 side rail spacer.
| 2. INSTALL REAR NO. 3 SIDE RAIL SPACER RH |
| 3. INSTALL REAR NO. 2 SIDE RAIL SPACER LH |
Attach the 2 claws to install the rear No. 2 side rail spacer.
| 4. INSTALL REAR NO. 2 SIDE RAIL SPACER RH |
| 5. INSTALL SIDE RAIL SPACER |
Attach the 2 claws to install the side rail spacer.
| 6. INSTALL FRONT SIDE RAIL SPACER LH |
Attach the 2 claws to install the front side rail spacer.
| 7. INSTALL FRONT SIDE RAIL SPACER RH |
| 8. INSTALL ROOF HEADLINING ASSEMBLY |
![]() |
Place the roof headlining into the vehicle as shown in the illustration.
w/o Rear Cooler:
Install the roof headlining with the clips.

| *A | w/o Assist Grip | - | - |
w/ Rear Cooler:
Attach the 5 fasteners to install the roof headlining.
Install the clips.

| *A | w/o Assist Grip | - | - |
Connect the connectors and attach the 4 clamps.
Attach the 4 clamps to the front pillar.
| 9. INSTALL DEFROSTER NOZZLE ASSEMBLY |
Attach the 4 clips to install the defroster nozzle assembly.
| 10. INSTALL NO. 3 HEATER TO REGISTER DUCT |
Attach the 4 claws to install the No. 3 heater to register duct.
Install the clip.
| 11. INSTALL NO. 1 HEATER TO REGISTER DUCT |
Attach the 3 claws to install the No. 1 heater to register duct.
Install the clip.
| 12. INSTALL NO. 2 HEATER TO REGISTER DUCT |
Install the No. 2 heater to register duct with the 3 clips.
| 13. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY |
Attach the 3 guides, 2 claws and 3 clips to install the lower instrument panel finish panel.
| 14. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY |
| 15. INSTALL ASSIST GRIP |
Install the assist grip with the 2 screws.
Attach the 4 claws to close the 2 covers.
| 16. INSTALL VISOR HOLDER LH |
Attach the 2 claws to install the visor holder.
Install the screw.
| 17. INSTALL VISOR HOLDER RH |
| 18. INSTALL VISOR ASSEMBLY LH |
Install the visor with the 2 screws.
Attach the guide.
| 19. INSTALL VISOR ASSEMBLY RH |
| 20. INSTALL NO. 1 ROOM LIGHT ASSEMBLY |
![]() |
Connect the light connector.
Install the room light with the 2 screws.
Attach the 4 claws to install the lens.
| 21. INSTALL COOLER CONTROL SWITCH ASSEMBLY (w/ Rear Cooler) |
Connect the connector.
![]() |
Attach the 2 clips to install the cooler control switch assembly (rear blower control switch) as shown in the illustration.
| 22. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror) |
![]() |
| 23. INSTALL MAP LIGHT ASSEMBLY |
Connect the connector.
Attach the 2 guides and claw.
Install the 2 screws to install the map light assembly.
| 24. INSTALL INNER UPPER ROOF SIDE GARNISH LH |
Attach the clip to install the inner upper roof side garnish.
Install the clip.
w/ Rear No. 2 Seat:
Connect the rear No. 2 seat belt shoulder anchor with the bolt.
Attach the 2 claws to close the rear No. 2 seat belt shoulder anchor cover.
| 25. INSTALL INNER UPPER ROOF SIDE GARNISH RH |
| 26. INSTALL QUARTER PILLAR GARNISH LH |
Attach the 9 clips to install the quarter pillar garnish.
Connect the rear No. 1 seat belt shoulder anchor with the bolt.
Attach the 2 claws to close the rear No. 1 seat belt shoulder anchor cover.
| 27. INSTALL QUARTER PILLAR GARNISH RH |
| 28. INSTALL QUARTER INSIDE TRIM BOARD LH |
Connect the power point socket connector.
Detach the 7 claws and 10 clips to install the quarter inside trim board.
Install the clip.
w/ Rear No. 2 Seat:
Connect the rear No. 2 seat outer belt floor anchor with the bolt.
Connect the rear No. 1 seat outer belt floor anchor with the bolt.
Attach the 2 claws to install the outer lap belt anchor cover.
| 29. INSTALL QUARTER INSIDE TRIM BOARD RH |
Detach the 8 claws and 10 clips to install the quarter inside trim board.
Install the clip.
w/ Rear No. 2 Seat:
Connect the rear No. 2 seat outer belt floor anchor with the bolt.
Connect the rear No. 1 seat outer belt floor anchor with the bolt.
Attach the 2 claws to install the outer lap belt anchor cover.
| 30. INSTALL QUARTER TRIM HOOK |
Install the quarter trim hook with the screw.
| 31. INSTALL BACK DOOR SCUFF PLATE |
Attach the 4 claws, 2 guides and 6 clips to install the back door scuff plate.
| 32. INSTALL CENTER PILLAR GARNISH LH |
Attach the guide and clip to install the center pillar garnish.
Connect the front seat belt shoulder anchor with the bolt.
Attach the 4 claws to install the front seat belt shoulder anchor cover.
| 33. INSTALL CENTER PILLAR GARNISH RH |
| 34. INSTALL LOWER CENTER PILLAR GARNISH LH |
Attach the 2 claws, 2 guides and 2 clips to install the lower center pillar garnish.
Connect the front seat outer belt floor anchor with the bolt.
Attach the 2 claws to install the outer lap belt anchor cover.
| 35. INSTALL LOWER CENTER PILLAR GARNISH RH |
| 36. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Align the paint mark on the rear door opening trim weatherstrip with the mark position on the vehicle and install the rear door opening trim weatherstrip as shown in the illustration.
| *1 | Paint Mark |
| *2 | Mark Position |
| 37. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH |
| 38. INSTALL REAR DOOR SCUFF PLATE LH |
Attach the 2 clips and 7 claws to install the rear door scuff plate.
| 39. INSTALL REAR DOOR SCUFF PLATE RH |
| 40. INSTALL FRONT PILLAR GARNISH LH |
w/ Curtain Shield Airbag:
Remove the protective cover.
Attach the 2 guides and 2 clips to install the front pillar garnish.
| 41. INSTALL FRONT PILLAR GARNISH RH |
| 42. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY |
Install the assist grip with the 2 screws.
| 43. INSTALL ASSIST GRIP PLUG LH |
Attach the 2 claws to install the assist grip plug.
| 44. INSTALL ASSIST GRIP PLUG RH |
| 45. INSTALL FRONT DOOR OPENING TRIM LH |
![]() |
Align the paint mark on the front door opening trim with the mark position on the vehicle and install the front door opening trim as shown in the illustration.
| *1 | Paint Mark |
| *2 | Mark Position |
| 46. INSTALL FRONT DOOR OPENING TRIM RH |
| 47. INSTALL FRONT DOOR SCUFF PLATE LH |
Attach the 3 clips and 7 claws to install the front door scuff plate.
| 48. INSTALL FRONT DOOR SCUFF PLATE RH |
| 49. INSTALL TONNEAU COVER HANGER LH (w/ Tonneau Cover) |
Install the tonneau cover hanger with the screw.
| 50. INSTALL TONNEAU COVER HANGER RH (w/ Tonneau Cover) |
| 51. INSTALL TONNEAU COVER HOLDER LH (w/ Tonneau Cover) |
Install the tonneau cover holder with the screw.
| 52. INSTALL TONNEAU COVER HOLDER RH (w/ Tonneau Cover) |
| 53. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) |
Install the tonneau cover.
| 54. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (w/ Rear No. 2 Seat) |
| 55. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (w/ Rear No. 2 Seat) |
| 56. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 57. CHECK SRS WARNING LIGHT |