Home › ENGINE · 1KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for i-ART)

DTC    P167A    Lost Communication with Injector #1

DTC    P167B    Lost Communication with Injector #2

DTC    P167C    Lost Communication with Injector #3

DTC    P167D    Lost Communication with Injector #4

for Preparation Click here


DESCRIPTION


P167A, P167B, P167C, P167D 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 3 minutes or more
Communication between the ECM and injector assembly is lost for 4 seconds or more.
(1 trip detection logic)
  1. Injector assembly
  2. Harness and connector

MONITOR DESCRIPTION

If the ECM detects that there is a communication problem with an injector for a certain amount of time continuously, it illuminates the MIL.
A DTC is assigned for each cylinder. However, the cylinders cannot be distinguished. If there is no problem with the communication line, replace all the injector assemblies.

HINT:
If there is a problem with the communication line, the fuel temperature for the cylinder which has a communication problem does not change when "Fuel Temperature" is confirmed in the Data List.


A281122E01


WIRING DIAGRAM

Refer to DTC P0201 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.CHECK FOR ANY OTHER DTCS OUTPUT
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P167A, P167B, P167C and P167D are output
    A
    P13A1, P13A2, P13A3, P13A6, P13A7, P13A8, P13AB, P13AC, P13AD, P13B1, P13B2, P13B3, P13C3, P13C8, P13CD, P13D3 and P167A, P167B, P167C, P167D are output
    B



B
GO TO FUEL PRESSURE SENSOR CIRCUIT (Click here)
A


2.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM)
  1. Disconnect the injector assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    F31-5 (CINJ) - E30-22 (CINJ)
    Always
    Below 1 Ω
    F32-5 (CIJ2) - E30-22 (CINJ)
    Always
    Below 1 Ω
    F33-5 (CIJ3) - E30-22 (CINJ)
    Always
    Below 1 Ω
    F34-5 (CIJ4) - E30-22 (CINJ)
    Always
    Below 1 Ω
    F31-5 (CINJ) or E30-22 (CINJ) - Body ground
    Always
    200 kΩ or higher
    F32-5 (CIJ2) or E30-22 (CINJ) - Body ground
    Always
    200 kΩ or higher
    F33-5 (CIJ3) or E30-22 (CINJ) - Body ground
    Always
    200 kΩ or higher
    F34-5 (CIJ4) or E30-22 (CINJ) - Body ground
    Always
    200 kΩ or higher

  1. Reconnect the injector assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT INJECTOR ASSEMBLY


    A321482E02
  1. Disconnect the injector assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    5 (CINJ) - 1 (EIJ1)
    Always
    600 to 1400 kΩ
    5 (CIJ2) - 1 (EIJ2)
    Always
    600 to 1400 kΩ
    5 (CIJ3) - 1 (EIJ3)
    Always
    600 to 1400 kΩ
    5 (CIJ4) - 1 (EIJ4)
    Always
    600 to 1400 kΩ

    Text in Illustration 
    *1
    Ohmmeter
    *a
    Component without harness connected
    (Injector Assembly)

    HINT:
    1. If there is an injector assembly that is outside the specified range, only replace that injector assembly.
    2. Even when the resistance is within the specified range, the injector assembly may be malfunctioning. Therefore, if all of the injector assemblies are within the specified range, replace all of the injector assemblies.

  1. Reconnect the injector assembly connector.


NEXT


4.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)
  1. Replace the injector assembly (Click here).

    NOTICE:
    1. Replace the injector assembly according to the results of the resistance inspection.
    2. When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
    3. Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
    4. If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
    5. If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
    6. If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.


NEXT


5.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


6.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds

  1. Turn the ignition switch to ON for 3 minutes or more.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END