Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM

NAVIGATION SYSTEM > Microphone Circuit between Microphone and Navigation Receiver Assembly


DESCRIPTION

  1. The navigation receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
  2. Using this circuit, the navigation receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the navigation receiver assembly.

WIRING DIAGRAM


E278095E07


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
  1. Disconnect the N5 navigation receiver assembly connector.

  1. Disconnect the M3 map light assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N5-4 (MACC) - M3-4 (MACC)
    Always
    Below 1 Ω
    N5-5 (MIN+) - M3-3 (MCO+)
    Always
    Below 1 Ω
    N5-19 (MIN-) - M3-2 (MCO-)
    Always
    Below 1 Ω
    N5-4 (MACC) - Body ground
    Always
    10 kΩ or higher
    N5-5 (MIN+) - Body ground
    Always
    10 kΩ or higher
    N5-19 (MIN-) - Body ground
    Always
    10 kΩ or higher
    N5-18 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK NAVIGATION RECEIVER ASSEMBLY


    E286789E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N5-18 (SGND) - Body ground
    Always
    Below 1 Ω
    N5-19 (MIN-) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N5-4 (MACC) - Body ground
    Ignition switch ACC
    4 to 6 V

Text in Illustration 
*a
Component with harness connected
(Navigation Receiver Assembly)


NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK


3.CHECK MAP LIGHT ASSEMBLY
E244515E06
  1. Turn the ignition switch to ACC.

  1. Connect an oscilloscope to terminals 3 (MCO+) and 2 (MCO-) of the map light assembly connector.

  1. Check the waveform of the telephone microphone assembly using the oscilloscope.
    Result 
    Result
    Proceed to
    A waveform synchronized with the voice input to the map light assembly is output
    A
    A waveform synchronized with the voice input to the map light assembly is not output
    B
    Text in Illustration 
    *a
    Component with harness connected
    (Map Light Assembly)



B
Go to step 4
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

4.CHECK TELEPHONE MICROPHONE ASSEMBLY
  1. Replace the telephone microphone assembly with a new or normally functioning one (Click here).

  1. Check if the same problem occurs again.
    Result 
    Result
    Proceed to
    Malfunction disappears
    A
    Malfunction does not disappears
    B



B
Go to step 5
A

END (TELEPHONE MICROPHONE IS DEFECTIVE) 

5.CHECK MAP LIGHT ASSEMBLY
  1. Replace the map light assembly with a new or normally functioning one (Click here).

  1. Check if the same problem occurs again.
    Result 
    Result
    Proceed to
    Malfunction disappears
    A
    Malfunction does not disappears
    B



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A

END (MAP LIGHT ASSEMBLY IS DEFECTIVE)