Display Function
Symptom
| Suspected Area
| See page
|
Pressing ignition switch does not turn on system
| Proceed to "Navigation Receiver Assembly Power Source Circuit"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Black screen (No image appears on navigation/audio screen)
| Proceed to "Black Screen"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Display does not dim (does not change to night screen) with tail switch on
| Proceed to "Display does not Dim when Light Control Switch is Turned ON"
|
Click here
|
Proceed to "Illumination Circuit"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Power does not turn off (Screen remains on)
| Proceed to "Navigation Receiver Assembly Power Source Circuit"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Screen is distorted
| Proceed to "Navigation Receiver Assembly Power Source Circuit"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Screen flicker or color distortion
| Proceed to "Screen Flicker or Color Distortion"
|
Click here
|
Proceed to "Navigation Receiver Assembly Power Source Circuit"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Navigation Function
Symptom
| Suspected Area
| See page
|
Navigation screen is not displayed when "HOME" switch is pressed (warning message is displayed and navigation system continues to operate in audio mode)
| SD card
| -
|
GPS mark is not displayed
| Proceed to "GPS Mark is not Displayed"
|
Click here
|
Navigation antenna cord sub-assembly
|
Click here
|
Navigation antenna assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Date and time on navigation screen is different from actual date and time
| Proceed to "GPS Mark is not Displayed"
|
Click here
|
Navigation antenna cord sub-assembly
|
Click here
|
Navigation antenna assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Vehicle position mark deviates from correct position and does not return to correct position
| Proceed to "GPS Mark is not Displayed"
|
Click here
|
Navigation antenna cord sub-assembly
|
Click here
|
Navigation antenna assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Cursor or map rotates when vehicle is stopped
| Proceed to "Cursor or Map Rotates when Vehicle Stopped"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Vehicle position mark moves in the opposite direction to the vehicle
| Proceed to "Cursor or Map Rotates when Vehicle Stopped"
|
Click here
|
Proceed to "Reverse Signal Circuit"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Vehicle position mark deviates from and returns to correct position repeatedly even though GPS mark is displayed
| Proceed to "GPS Mark is not Displayed"
|
Click here
|
Drive the vehicle for sensor learning (At a place where GPS signals can be received, drive the vehicle clockwise and counterclockwise in at least a 200 meter square 2 times or more)
| -
|
Navigation antenna cord sub-assembly
|
Click here
|
Navigation antenna assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Vehicle position mark moves slow or fast
| Proceed to "GPS Mark is not Displayed"
|
Click here
|
Navigation antenna cord sub-assembly
|
Click here
|
Navigation antenna assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Voice guidance does not function
| Proceed to "Voice Guidance does not Function"
|
Click here
|
Proceed to "Speaker Circuit"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Map display is incomplete
| SD card
| -
|
Navigation receiver assembly
|
Click here
|
Route cannot be calculated
| Proceed to "Route cannot be Calculated"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Navigation system cannot record memory point registration or each item setting
| Navigation receiver assembly
|
Click here
|
A message indicating to wait for a while because of low temperature is displayed
| Start the engine and increase cabin temperature (Near navigation receiver assembly)
| -
|
Navigation receiver assembly
|
Click here
|
A message is displayed because map data cannot be read, and current position screen is not displayed
| If message appears only when driving on rough roads, check if message disappears when vehicle is stopped
| -
|
SD card
| -
|
Navigation receiver assembly
|
Click here
|
Map screen turns white or blue (GPS receiving status is displayed normally, and switches and own vehicle position mark are also displayed normally)
| Change map scale to smallest (a scale that shows a large area)
| -
|
SD card
| -
|
Navigation receiver assembly
|
Click here
|
Reverse signal does not change in vehicle signal check mode
| Proceed to "Reverse Signal Circuit"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Parking brake switch signal does not change in vehicle signal check mode
| Proceed to "Parking Brake Switch Circuit"
|
Click here
|
Navigation receiver assembly
|
Click here
|
CD or DVD Player Function
Symptom
| Suspected Area
| See page
|
Disc cannot be played or player does not function with disc
| Proceed to "Disc Player Outline" in System Description and check if the disc is compatible with the disc player
|
Click here
|
Navigation receiver assembly
|
Click here
|
Disc cannot be inserted/played or disc is ejected right after insertion
| Proceed to "Disc cannot be Inserted or is Ejected Right After Insertion"
|
Click here
|
Disc cannot be ejected
| Proceed to "Disc cannot be Ejected"
|
Click here
|
Disc sound skips
| Proceed to "CD/DVD Sound Skips"
|
Click here
|
While vehicle is stopped, DVD cannot be viewed even when parking brake is set (Parking brake switch is on)
| Proceed to "Parking Brake Switch Circuit"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Screen color is poor only when watching DVD
| Change the color settings on the screen adjustment screen
| -
|
Sound quality is bad only when disc is played (Volume is too low)
| Proceed to "Sound Quality is Bad Only when Disc is played (Volume is Too Low)"
|
Click here
|
When the disc is playing, some cover art may not be displayed
| When a song unregistered to the Gracenote CDDB is playing, its cover art cannot be displayed
| -
|
When the disc is playing, cover art cannot be displayed
| Navigation receiver assembly
|
Click here
|
AUX (Stereo Jack) Function
Symptom
| Suspected Area
| See page
|
External device sound cannot be heard or sound quality is bad (Stereo jack is used)
| Proceed to "Sound Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
"AUX/VTR" is not displayed on system check mode screen
| Proceed to "Sound Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Screen is distorted or not displayed only when using the device connected to the No. 1 stereo jack adapter assembly
| Check if appropriate image signal setting (NTSC/PAL) is selected
| -
|
Connect a known good device to the No. 1 stereo jack adapter assembly and check if the image is output
| -
|
Connect using a known good cable and check if the image is output
| -
|
Proceed to "Display Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Screen color is abnormal only when using the device connected to the No. 1 stereo jack adapter assembly (Screen color is normal in other modes)
| Check adjustment of image quality (make sure that each setting is set to the middle)
| -
|
Check using a known good device or check if similar symptoms occur on another vehicle of the same model using the device
| -
|
Navigation receiver assembly
|
Click here
|
"Bluetooth" Hands-free Function
Symptom
| Suspected Area
| See page
|
"Bluetooth" is inoperative (In-vehicle device cannot be recognized by the cellular phone)
| Proceed to "Cellular Phone Inspection"
|
Click here
|
Navigation receiver assembly
|
Click here
|
"Bluetooth" compatible cellular phone cannot be registered
| Proceed to "Cellular Phone Registration Failure"
|
Click here
|
"Bluetooth" compatible cellular phone cannot be connected
| Check that no other cellular phone is connected as a hands-free device
| -
|
Bring the cellular phone near the in-vehicle device and reconnect it
| -
|
Proceed to "Cellular Phone Inspection"
|
Click here
|
Navigation receiver assembly
|
Click here
|
"Bluetooth" compatible cellular phone cannot be connected automatically (can be connected manually)
| Check that "Bluetooth" automatic connection setting of the in-vehicle device is on
| -
|
Navigation receiver assembly
|
Click here
|
"Bluetooth" compatible cellular phone connection is disconnected
| Bring the cellular phone near the in-vehicle device and check if it is reconnected
| -
|
Proceed to "Cellular Phone Inspection"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Message that prompts to check the cellular phone is displayed
| Bring the cellular phone near the in-vehicle device and check if it is reconnected
| -
|
Proceed to "Cellular Phone Inspection"
|
Click here
|
Navigation receiver assembly
|
Click here
|
When the ignition switch is turned to ACC, instructions for checking the connection condition between the in-vehicle device and cellular phone are displayed
| Turn the cellular phone connection conformation display on the in-vehicle device off
| -
|
Phonebook data cannot be transferred
| Check that the phonebook automatic transfer setting of the in-vehicle device is on
| -
|
Check that no applications on the cellular phone are running
| -
|
If using "Bluetooth" audio function, cancel the "Bluetooth" audio player connection and check the operation
| -
|
Transfer phonebook data manually
| -
|
Proceed to "Cellular Phone Inspection"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Phonebook data is cleared
| Navigation receiver assembly
|
Click here
|
Phonebook data cannot be edited
| Check that the phonebook data automatic transfer setting is off
| -
|
Navigation receiver assembly
|
Click here
|
All the transferred phonebook data is sorted to "Other"
| Check that no applications on the cellular phone are operating
| -
|
Check that phonebook data in the cellular phone is not stored to the SIM card
| -
|
Proceed to "Cellular Phone Inspection"
|
Click here
|
Explain to the customer that all the transferred phonebook data may be stored to "Other" depending on cellular phone
| -
|
Cellular phone cannot make outgoing/ incoming calls
| Move the vehicle into a cellular phone service area, check that the "Bluetooth" device is connected to the vehicle and operate device again
| -
|
Check that the cellular phone can make outgoing/incoming calls properly when not connected via "Bluetooth"
| -
|
Proceed to "Cellular Phone Inspection"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Other caller's voice is interrupted by noise or sound quality is poor
| Check the receiving voice volume (if it is too high, voice may sound distorted)
| -
|
Make a call with the cellular phone disconnected from "Bluetooth" and check that other caller's voice can be heard clearly
| -
|
Proceed to "Check Hands-free Voice Quality Setting" in Operation Check
|
Click here
|
Proceed to "Cellular Phone Inspection"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Other caller's voice cannot be heard
| Check that reception voice volume is not set to minimum
| -
|
Make a call with the cellular phone disconnected from "Bluetooth" and check that other caller's voice can be heard clearly
| -
|
Proceed to "Check Hands-free Voice Quality Setting" in Operation Check
|
Click here
|
Proceed to "Cellular Phone Inspection"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Caller's voice (your voice) is interrupted by noise or sound quality is poor
| Check the transmitting voice volume (if it is too high, voice may sound distorted)
| -
|
Check that nothing can cause noise around the microphone (an outlet of the air conditioning system facing the microphone, wind from an open window, additional devices, etc. may affect noise occurrence)
| -
|
Proceed to "Check Hands-free Voice Quality Setting" in Operation Check
|
Click here
|
Proceed to "Cellular Phone Inspection"
|
Click here
|
Proceed to "Microphone Circuit between Microphone and Navigation Receiver Assembly"
|
Click here
|
Other caller cannot hear your voice
| When talking on the cellular phone, check that the mute button is not pressed
| -
|
Check that nothing can cause noise around the microphone (an outlet of the air conditioning system facing the microphone, wind from an open window, additional devices, etc. may affect noise occurrence)
| -
|
Proceed to "Check Hands-free Voice Quality Setting" in Operation Check
|
Click here
|
Proceed to "Cellular Phone Inspection"
|
Click here
|
Proceed to "Microphone Circuit between Microphone and Navigation Receiver Assembly"
|
Click here
|
"Bluetooth" Audio Function
Symptom
| Suspected Area
| See page
|
Portable player cannot be registered
| Proceed to "Portable Player cannot be Registered"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Portable player cannot be connected manually/automatically
| Proceed to "Portable Player cannot be Registered"
|
Click here
|
Proceed to "Portable Player cannot be Connected Manually/Automatically"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Cellular phone with portable audio function cannot be recognized as "Bluetooth" audio device even when connected using "Bluetooth"
| Proceed to "Portable Player cannot be Registered"
|
Click here
|
Proceed to "Portable Player cannot be Connected Manually/Automatically"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Sound of portable player cannot be heard from speakers, or sound is low
| Proceed to "Sound of Portable Player cannot be Heard from Speakers or Sound is Low"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Portable player does not play even after "Bluetooth" audio mode is selected
| Proceed to "Does not Play even after Bluetooth Audio Mode is Selected"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Portable player does not play
| Proceed to "Does not Play even after Bluetooth Audio Mode is Selected"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Track information such as track number, track name, elapsed play time and playlist is not displayed
| Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Operation switches for portable player such as play, pause, repeat, random and scan are not displayed
| Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Battery condition of portable player is not displayed
| Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device"
|
Click here
|
Navigation receiver assembly
|
Click here
|
"Bluetooth" signal condition is not displayed
| Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Portable player cannot pause, select file, fast forward, fast rewind, play at random or scan
| Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Noise occurs or sound skips when portable player plays
| Proceed to "Noise Occurs or Sound Skips when Portable Player Plays"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Registered device cannot be deleted
| Proceed to "Registered Device cannot be Deleted"
|
Click here
|
Navigation receiver assembly
|
Click here
|
USB Audio System Function
Symptom
| Suspected Area
| See page
|
USB audio system sound cannot be heard or sound quality is bad (USB connector is used)
| Proceed to "Data Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
USB device or "iPod" is not recognized
| Proceed to "USB Audio System Recognition/Play Error"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Track information such as track, artist and album names are not displayed
| Proceed to "USB Audio System Recognition/Play Error"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
USB device or "iPod" is recognized but cannot play, or can play but not in a sorted order
| Proceed to "USB Audio System Recognition/Play Error"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Album cover art cannot be displayed
| Check that Display Cover Art on the "iPod" Settings screen is set to on
| -
|
Check that a JPEG file is used for the cover art
| -
|
"iPod" battery cannot be charged
| Proceed to "USB Audio System Recognition/Play Error"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Screen is distorted or not displayed only when using the video function of an "iPod"
| Check if "iPod" is set to output images
| -
|
Check if appropriate image signal setting (NTSC/PAL) is selected
| -
|
Check if video sound input is set to "A/V"
| -
|
Connect using a known good cable and check if the image is output
| -
|
Proceed to "Data Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
USB-Video cannot play
| Proceed to "USB Audio System Outline" in System Description and check that the video file stored on the USB device is playable
|
Click here
|
Check that MOD data is not being downloaded through USB device
| -
|
Check that application data is not being downloaded through USB device
| -
|
Check that reprogramming data is not being downloaded through USB device
| -
|
Check that the CDDB is not being updated
| -
|
Check if the file can be played in another vehicle
| -
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
USB-Video cannot be recognized/selected
| Proceed to "USB Audio System Outline" in System Description and check that the video file stored on the USB device is playable
|
Click here
|
Check if any video files on the connected USB device can be played in another vehicle
| -
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
USB-Video screen is not displayed (Audio is output)
| Check if the USB-Video screen is displayed while the vehicle is stopped
| -
|
Proceed to "USB Audio System Outline" in System Description and check that the video file stored on the USB device is playable
|
Click here
|
Check that the file format does not only support audio
| -
|
Check if the file can be played in another vehicle
| -
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Screen color is poor only for USB-Video
| Restore display settings to their default values and play a USB-Video
| -
|
Check the color of other files on the USB device
| -
|
Check the screen color of other USB devices
| -
|
Check if the file can be displayed properly in another vehicle
| -
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
USB-Video sound cannot be heard or sound quality is bad
| Restore audio settings to their default values and play a USB-Video
| -
|
Check the sound of other files on the USB device
| -
|
Check the sound of other USB devices
| -
|
Check if the file can be played properly in another vehicle
| -
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Cannot change USB-Video settings
| Check if the USB-Video screen is displayed while the vehicle is stopped
| -
|
Refer to "USB-Video cannot play" above
| -
|
Digital TV Function
Symptom
| Suspected Area
| See page
|
While vehicle is stopped, digital TV image is not displayed
| Proceed to "Parking Brake Switch Circuit"
|
Click here
|
Check that the parental lock is unlocked
| -
|
Check if similar symptoms occur with another vehicle
| -
|
Proceed to "TV Screen is Distorted"
|
Click here
|
Image stops, noise occurs, or screen color is distorted only when watching digital TV
| Check the settings of the display quality adjustment screen (check that each setting is centered)
| -
|
Check if similar symptoms occur with another broadcast
| -
|
Proceed to "TV Screen is Distorted"
|
Click here
|
Sound cannot be heard, sound quality is poor or sound is interrupted only when watching digital TV
| Check the settings of the sound quality adjustment screen (check that each setting is centered)
| -
|
Check if similar symptoms occur with another broadcast
| -
|
Proceed to "TV Screen is Distorted"
|
Click here
|
Channels cannot be set (broadcast stations cannot be found by scanning)
| Move the vehicle to a place where the reception sensitivity is good and check again
| -
|
Proceed to "TV Screen is Distorted"
|
Click here
|
Broadcast station names are not displayed
| Check if similar symptoms occur with another broadcast
| -
|
Move the vehicle to a place where the reception sensitivity is good and check again
| -
|
Proceed to "TV Screen is Distorted"
|
Click here
|
Parental lock setting cannot be changed
| On the parental lock identification number input screen, press the left arrow switch 10 times and reset the number
| -
|